The most popular doors are made of oak, alder, pine and spruce. In our catalog you can choose and buy veneered, laminated, metal, painted, eco-veneer and PVC. Separately allocated building doors- they are the cheapest to buy, they are installed temporarily while repairs are underway and they are not a pity.
Our entrance doors- these are reliable and aesthetic models from the factories "Stardis", "Argus", "Condor" and "Logic". They are manufactured in accordance with the standards of protection, have a pleasing to the eye appearance and equipped with secure locks. We sell only original products from the manufacturer, so you are guaranteed to receive reliable protection from burglary and other types of penetration.
If you have any questions regarding the selection, payment and warranty service, please contact our managers by phone and through the website!
HOW TO REPLACE AN INTERIOR DOOR HANDLE? Door handles perform the functions of lock and door control. Aesthetic appearance door hardware allows you to decorate the door leaf. TYPES OF HANDLES Door handles can be: stationary - not connected with a lock or latch; movable - setting the lock mechanism in motion. Stationary handles can be in the form of a bracket or a ball, push handles have a long lever or a swivel round element. Handles can be made of wood, plastic metal. The surface of the wooden handles is polished and varnished. The appearance of the products is very aesthetic and gives a respectable appearance to the doors. The surface of the handles can be worn out, covered with scratches, but it is quite suitable for restoration. Plastic handles can imitate metal and glass products and have an original shape. They are inexpensive, but they break more often - in comparison with products made from other types of materials. Metal handles are usually made of brass, aluminum, of stainless steel or hard alloys. The surface is chrome plated or has other types protective coatings. Such handles are the least susceptible to deformation during intensive use. Sometimes glass or stone can be used to create original pens. In decorating products, rhinestones, stones, leather inserts, glass and other aesthetically attractive materials can be used. REASONS TO REPLACE THE HANDLE Need to replace door handle occurs due to: breakage of the handle or lock mechanism itself; interior design changes; unattractive appearance as a result of the appearance of scuffs and chips. How to replace a door handle? It is necessary to perform a number of simple actions using a conventional screwdriver. REPLACING THE STATIONARY HANDLE Handles that are not related to the lock control are attached directly to the door leaf. To replace a door handle of this type, it is enough to unscrew the old screws with a screwdriver or screwdriver, restore the hole and attach a new handle. HOW TO REPLACE A PUSH LEVER DOOR HANDLE? These pens are the most popular. To replace them, you will need a screwdriver, in some cases a hex wrench. In the recess at the base of the handle is a screw that must be unscrewed. After that, the lever is removed, then the decorative trim is removed or unscrewed. The next step is to unscrew the main screws that secure the structure to the door leaf. When performing this operation, it is necessary to hold the handle with reverse side doors. By pulling the structure towards you, you can release the handle along with the rotary axis. If there is a need to replace the lock or latch, unscrew the screws that secure the bar to the end of the door, and then remove the main mechanism. The steps for installing a new handle must be performed in the reverse order of the disassembly process. REPLACING THE ROTARY HANDLES WITH SOCKETS How to replace a knob interior door, made in the form of a swivel ball? The sequence of actions here is similar to those when replacing lever handles. It is necessary to find a recess and unscrew the fixing screw. However, in some cases, it is enough to hold the handle motionless on one side and unscrew the round element from the thread on the back of the door. There are designs when it is enough to pull one of the parts towards itself with a certain effort, provided that the other part is fixed fixed. Then the socket is removed, and the screws that serve to fasten the main structure are unscrewed. DISMANTLING AND INSTALLATION OF KNOB HANDLES Knobs are a popular type of handle. They differ from conventional rotary knobs in the presence of a decorative flange of a larger diameter (compared to rosettes) and in lightness of construction. The replacement process consists of several stages: pressing the locking pin with a screwdriver or other sharp object and simultaneously removing the decorative part of the handle; removing the decorative flange by prying with a screwdriver in the area of a special recess; unscrewing the screws fastening the two parts of the knob-knob; recesses of the design of the handle from the door. Sometimes a special key is included with the knob-knob. It is intended for fixing a spring pin in the technological hole. Installation steps are reversed: the location of one part of the handle in the recess in the door leaf; putting on a round mounting plate on the other side; screwing in the fixing screws; the location of the decorative flange on the axis of the structure; nozzle decorative push handle. Majority modern models lever handles have designs that allow you to easily replace yourself. However, expensive pens can have complex device requiring special knowledge. It is more efficient to turn to the services of professionals. DOORS AND ACCESSORIES IN THE RUSSDVERI ONLINE STORE The RUSSDVERI online store offers a wide range of Russian and Belarusian manufacturers and related accessories. Customers can use the services of RussDoors specialists, who will qualitatively install doors, locks, handles and other fittings. The quality of goods offered by our online store is confirmed by certificates. Handles and doors purchased from us will last a long time. The need for replacement can arise only if you want to change the interior design, and not because of the failure of products. A wide range makes it possible to choose fittings that are most suitable for the design of the door and the interior as a whole. Our company offers competitive prices, allowing you to significantly reduce the cost of repairs. Using the action when buying doors, accessories can be received as a gift.
It will be useful for any owner to know how to disassemble the handle on the door, especially the interior one. This fitting is subjected to a serious test by all tenants, so someday it will fail, and it will need to be replaced with another one. In this case, you do not need to call specialists, you can handle it yourself, while saving on the employee's wages. Moreover, this business does not require great skill, but only a little skill. The dismantling process may differ depending on the type of handle, but the whole process should not cause any particular difficulties.
How to remove the handle from the interior door? Before proceeding with the analysis of the mechanism, you need to find out what kind of classification it belongs to. The division is based on several criteria. The one described below is suitable specifically for parsing a pen, because it has a classification according to design features.
Press. Such a handle is attached on both sides of the door leaf and has L-shape. Opening occurs due to the load on the handle, after which the tongue is set in motion. The disadvantage of this fitting is that it is very traumatic.
Swivel. The opening method is the same as that of the push, only the tongue is set in motion not by pressing the handle, but by turning it. Such models are often not very convenient, because to scroll it, you need to have your hands dry, otherwise they will slip. When replacing them, a reasonable question arises about how to unscrew the interior door handle.
Stationary. This handle does not have a latch. It is attached with screws directly to the door leaf. It happens one- or two-sided, while it has an axial connecting element.
It is not so difficult to disassemble any of the models of door handles, because they have a similar design.
At the same time, it is extremely rare to carry out the analysis of this fitting. What reasons can lead to this? How to remove the handle from the interior door?
The first reason is breakdown. It occurs most frequently. Often, inexpensive Chinese models are prone to breakdowns, which are not designed for a constant and rough load. If the prevention of some elements is not observed, then the fittings become unusable. It should be repaired, and sometimes the entire element should be replaced.
The next reason is the need for replacement. Every year the market is replenished with new and improved models. At the same time, you can choose color scheme suitable for the interior, or put a new, more functional and reliable model.
Renovation in a room often involves a change in style. Do not ignore the door handles. Therefore, the question often arises of how to disassemble the door handle.
Another reason is the spoiled appearance. If the part is made of low-quality material, then scuffs and scratches will be visible on it very soon, which negatively affects the entire interior.
How to remove the handle from an interior push-type door? This mechanism is more difficult to disassemble, because in its design there is an axis rod, due to which the handle is held. It is tightened with a tetrahedron.
The process of parsing the handle must begin with the removal of the plugs around it. They are fastened with screws or tightly pressed. They are very easy to remove with a minus screwdriver.
On one side of the door, you need to unscrew the fittings and remove. Then the second part is removed, on which the axis rod remains.
If the handle is with then it is also removed.
Following the sequence and accuracy will allow you to remove the mechanism without problems, without damaging the parts and without creating unnecessary hassle.
When there is no hole on the side of the swivel type fittings into which a key or screwdriver can be inserted, the elements are separated manually. Both parts of the handle should be turned in different sides and gradually remove from the thread. On one of them there will be an axial rod.
In this way, the socket is removed and the screws are unscrewed. When the axis is removed, you can do the following elements - a latch or lock, if necessary. When decorative parts are removed, you need to monitor the use of your strength, because overdoing it can damage the elements.
The handle with a lock for interior doors of a rotary type is removed as follows.
This will require a key to clamp the spring mechanism. Often it is not included in the package with the product, but it can easily be replaced by a nail or other thin object.
The first step is to remove the decorative plates, which can simply be pry off with a sharp object.
Use a key or nail to move the spring-loaded pin by inserting the tool into the technological hole located on the side. At the same time, pull the handle and remove it together with the cap.
After that, you need to move the fastening screws located on the plate. Then the two parts of the handle can be removed together with the axle.
Assembling the round door handles back is not difficult, only all the steps must be done in reverse order. First comes which is fixed with a plate, then an axis is inserted, fasteners are put on it. Decorative inserts are mounted last. The main thing is not to forget that the decorative flange is first threaded, and only then the main part of the handle is attached.
How to disassemble a fixed type door handle? They are the least likely to break or deform. This is due to the lack of moving elements in it. Often, door handles of this type are not repaired after removal, but are changed entirely. The withdrawal process is as follows:
This design may not have a central rod, which greatly reduces the process. You only need to choose the right screwdriver to unscrew the screws of a certain diameter.
First of all, when dismantling the latch handle for interior doors with an automatic lock, you need to remove the screws with a screwdriver. Next, unfasten the overlays. Use to unscrew the rod.
After that pull out rotary mechanism coiled with a spring.
There are several ways in which the latch handle for interior doors is removed. round shape with latch. Here is the most popular one.
It is necessary to remove it with a screwdriver, first from the part where the latch device is located. It is necessary to press on the opened stopper and at the same time pull the handle towards you.
Then the latch is pulled out, for which the screws are unscrewed, after which the latch is released.
Thus, disassembling any door handle with your own hands is not a big problem.
The Chinese iron door is an economical and even quite nice solution. But there are many questions about its quality. Starting from the main material ( metal sheet), which is easy to cut with an ordinary can opener, and ending with the supplied fittings. And one of typical problems faced by the owners of Chinese doors - the handle of the Chinese iron door. This will be discussed further.
So what can be done in this case?
The first is to completely replace the lock along with all the components. The most expensive and not the most easy way but reliable.
The second is to find exactly the same set of handles with decorative frames together. Finding them is difficult, but possible. At the same time, the issue price is about 600 rubles.
Third - replacing the handle Chinese door. This is the most cheap option, since a suitable set of pens can be found for 200 rubles. But you'll have to tinker. It is this option that we will consider.
Chinese iron door handle replacement
If the handle of the Chinese door is broken, then we begin by unscrewing the screws that secure the decorative frame of the lock.
Next, just remove the frame with all the contents, including the broken handle.
Next, we disassemble the spring mechanism of the handle. the main problem may occur with a clamping washer. Not afraid that it will break or burst, we bend it with a small flat screwdriver.
All! Frame disassembled, broken handle removed.
The frame can be put in place, but a piece of the handle will be needed to go to the store. According to it, or rather, according to its fastening, we will choose a new one. And the frame is put in place so that the door can be closed.
After the set of handles is purchased (sold only in sets), we install one handle instead of the damaged one, or both at once. We act in reverse order.
And at the end we install a decorative frame of the lock along with a new handle on the door.
Plastic windows are not as simple products as it might seem. All sash positions are controlled by just one handle, which transfers forces to numerous gears of fittings. No wonder the handle is the first to fail. plastic window, because it is constantly pulled, turned, twisted. But there can be problems immediately after installing the windows, if they are not adjusted accurately enough or have a factory defect. Although there may be other reasons. If you install plastic windows in compliance with all technologies and nuances, and then carefully operate them, they can last for many years without the need for repair. But if, nevertheless, the handle for the plastic window is broken, or it is stuck in any position, or it does not turn, or it does not turn all the way, then do not despair, you can fix this problem yourself. In this article, we will talk about how to disassemble the handle of a plastic window, how to adjust it, repair it or replace it with a new one, without resorting to the help of specialists. To do this, you need straight arms, a 4 mm L-shaped hex wrench, a Phillips screwdriver and a quick-witted head on your shoulders.
It is quite possible that you have encountered such a problem - the window handle is in a position that absolutely does not correspond to the position of the sash, and it is impossible to turn the handle - it is jammed. For example, the sash can be open and the handle in the "closed" position. You were just about to close the window, but it doesn’t work, since it’s impossible to turn the handle. What to do? First of all, do not pull the handle hard, this will not bring a positive result. The reason for the jamming of the plastic window handle is that it did not work in time blocker.
Almost all modern windows equipped with a special lock that blocks the turning of the handle. This was done for a good purpose - so that you do not inadvertently break the window. When you turn the handle to the tilt position (the handle looks up) or to the rotary position (the handle is horizontal), the lock is activated and prevents the handle from turning unintentionally. It happens that the blocker does not work in time. Most often this happens if you move the position of the handle too quickly. How to repair the handle of a plastic window in this case? First of all, it is necessary to determine the manufacturer of the fittings, the method of disabling the blocker will depend on this.
The name of the fittings can be seen on any metal part of the window. This is easy to do if the sash is in open position. Most often, the name is just in the area of \u200b\u200bthe handle, on the end of the sash.
If you have AUBI fittings: To disengage the bollard, the sash must be in a vertical position. If it is in the tilt-and-turn position, then the blocker located on the top hinge will also prevent the handle from turning. Therefore, we translate the sash into a vertical position, then in the area of \u200b\u200bthe handle on the end part of the sash we find a plate with a spring. It must be pressed against the seal, and then turn the handle to the position characteristic of the sash.
If you have accessories "Maco", "Roto", "GU", "Winkhaus": also in the area of the handle on the sash we find a metal plate, which is not located vertically, but is at an angle to the frame and sash. It must be pressed so that it becomes parallel to the frame, i.e. strictly vertically, then turn the handle to the desired position.
If, when you try to close the window, the handle still does not turn, then you should check whether the blocker is in contact with the response mechanism. A situation is possible when the blocker slips past without catching on the mechanism. The reason is thermal expansion.
If you notice that the blocker “slips”, then you need to open the sash, find the response mechanism, unscrew the screws with which it is screwed to the frame, then remove it, put something between it and the frame and screw it into place. As a lining, you can use a piece of thin plastic. As a result, the response mechanism should be located further from the frame, and the blocker should be hooked on it. Try again to close the window. If so, then the repair is complete.
The nuances of Winkhaus fittings: some models of windows with this fitting are equipped only with a lock located on the scissors of the tilt-and-turn mechanism. During operation, this blocker wears out as a result of constant friction, so it may fail over time. This is characterized by the fact that the handle can only be turned to the “open” position (horizontal) or to the tilt-and-turn position, for ventilation (handle up). In such a situation, you should not try to close the window and turn the handle with great effort. The gearbox of the main constipation may break. This is the case when it is better to entrust repairs to professionals, especially if the windows are still under warranty. If you intend to solve the problem yourself, you will have to remove the window sash.
On the upper hinge of the sash must be removed decorative overlay, then pull out the pin holding the sash in the frame. To do this, use a screwdriver and pliers. Carefully remove the sash from the hinges, put it on the floor and remove the scissors. To remove the scissors, it is necessary to unscrew the screws with which they are fixed. Remove the lock and install the scissors back.
If all the above procedures did not help, do not be zealous, contact the professionals.
The problem of another property is when the plastic window handle does not close, when you try to close the window, the handle does not turn to the end. At the same time, if you open the window and try to turn the handle to the “closed” position, after disabling / pressing the blocker, then the handle turns easily. There can be two reasons for such a problem.
First - dried grease in fittings. As already mentioned, the work of the window is provided by many transmission mechanisms, so their movement should be easy and smooth. If the grease in the fittings has dried up, or if dirt has got into it, then its work is disrupted. If the reason is only lubrication, then you can repair the plastic window handle yourself. To do this, you will need lubrication: either universal grease, or special grease for plastic windows, or, in extreme cases, WD-40 grease will do.
It must be poured into all moving fittings, this can be done through holes, including in the upper part of the fittings. Then it is necessary to turn the handle to one position, then to another, so the fittings will move and distribute the lubricant over its surface. If the reason is only lubrication, then this should be enough. If the reason is in the dirt that has clogged under the fittings, then it is better to invite the master, since you will have to remove all the fittings from the window and rinse it in a special bath.
Second - leaf sagging. This may not be visible to the naked eye, but even one millimeter will be enough to keep the handle from moving to the “closed” position.
Sash position "up-down" can be changed with the adjusting screws. It is necessary to remove the decorative cap from the lower sash of the plastic window. There is a hole for a 4mm hex wrench on the top of the hinge mechanism.
We insert the L-shaped key into the adjusting groove and turn it. If you turn it clockwise, the sash will rise, if you turn it counterclockwise, then it will fall. Each time, making several turns, we try to close the sash. In some types of fittings, the adjustment groove is located on the front surface of the hinge (as in the photo).
The sash can also be adjusted in a horizontal position - "left-right". Usually the top and bottom of the sash are adjusted separately.
The lower part is with the help of the lower loop. If you open the sash and look at side surface lower hinge, then an adjustment groove will also be noticeable on it. We insert a 5 mm hexagon into it and turn it. Clockwise - the sash moves to the left, counterclockwise - to the right.
The upper part of the sash is regulated by a mechanism located on the sash itself - at the top. For adjustment, the sash also needs to be opened, almost wide open. At the back, almost at the very top, there will be an adjustment groove. We insert a hexagon into it and turn it.
It happens that the handle of the plastic window just loosened. It scrolls to all positions, but nothing changes. The reason, most likely, is that the handle fastening has become loose, and the handle mechanism does not engage with the hardware mechanism. This problem is solved very easily.
The handle of the plastic window is adjusted using two screws, with which it is screwed to the sash. On the sash directly under the handle is decorative element- stub ( rectangular shape). It is necessary to carefully pry it with your hands, pulling it towards you, and then turn it 90 degrees. Those. the plug must be placed horizontally.
You will see two fixing screws - one on top of the handle, the other on the bottom. They must be tightened with a Phillips screwdriver.
This situation is rare, but it still happens: the pen can crack, break, or simply become unusable from old age. In this case, you will need to replace the handle on the plastic window. There is another reason to change the "native" handle, even if it is working, - the need to install a handle with a lock. When there are small children in the house and parents want to make sure that the child could not open the window or the door to the balcony himself, then special handles with locks are installed.
To remove the handle from the plastic window, you need to unscrew the two screws mentioned above. But first you need to open the sash so that the handle is in the “open” position. After the screws are unscrewed, it is necessary to remove them and then carefully remove the handle.
You can buy a new pen at construction market or in a building supermarket, as well as in a company that manufactures plastic windows. In addition to conventional handles, you can purchase a handle with a lock and even a "comb" that limits the opening of the window.
Installing the handle on a plastic window is done using the same screws that held the previous one, although you can use new ones. If you plan to install an opening limiter, then insert the regulator plate (“comb”) into the base of the handle. Then the pin of the handle is inserted into the hole, and the handle itself is screwed on.
Handles for plastic windows are produced not only by the same companies as fittings. For example, you can buy a pen made in China, Turkey, Austria, Germany, Great Britain, Poland and other countries. Window handles for plastic windows are considered to be consumable, they may differ in shape, but are necessarily universal and suitable for all window models and all fittings. The material of manufacture is aluminum, the most common color is white, but the handles can also be “wood-like”, gold or bronze. So you can choose the color of the windows. The shape can be rectangular, and rounded, and with notches for the fingers.
For a handle for a plastic window, the price practically does not depend on the shape, only on the quality and manufacturer, as well as on the color (non-white handles are more expensive). For example, a Chinese pen will cost only 2.5 USD, a Turkish one - 8.7 USD, a German and Austrian one - 10 USD. The price of a pen from the UK depends on the shape and ranges from $12 to $15. Handles for plastic windows with locks are a separate category: Polish ones will cost 25 USD, and the same analogue from the UK at 36 - 38 USD.
Repairing or replacing a plastic window handle is one of the easiest tasks in plastic window repair. It does not require qualifications or additional knowledge. The main thing is not to panic and follow the given instructions. If the above tips do not help, then be sure to call the wizard so that he can see the problem with his own eyes.
