Today, many people are faced with the question of how to integrate a dishwasher into a regular kitchen cabinet or under a countertop. Because purchasing such equipment is a rational and correct decision. However, its installation may cause some inconvenience. Don't despair ahead of time. You shouldn’t necessarily wait until you buy a new headset or make repairs. Below you will find information on how to integrate a dishwasher into a finished kitchen.
There are external machines that look like a separate device. They are installed where there is room for them. In appearance, they may resemble a washing machine. Typically, such equipment is small in size, so you can even place it above the countertop.
There are also partially built-in units at points of sale. It’s as if they are recessed into the furniture, but not completely covered. The control panel of the device is usually left. There should be no unnecessary problems with how to build a dishwasher under the countertop, for example.
There are also built-in appliances that are sold without doors. They are equipped with guides to which facades are attached made of the same materials as the buyer’s kitchen sets. On top of such appliances you can install panels that are screwed to the top of the countertops to make the appliance stable.
Installation of a dishwasher requires a separate electrical line, which is connected to sockets. Moreover, such an outlet will be used specifically for this device. Remember that they must be grounded so as not to take risks while using the equipment.
The equipment comes with a set of hoses that are needed to supply and drain water. It is recommended to leave access to these parts so that in an emergency you can get to them without unnecessary obstacles. If necessary, use a tee to supply electrical power to the equipment. In addition, do not forget about installing a tap (shut-off). Each part in the system requires sealing to prevent it from flooding. The drain hose is positioned so that the height level reaches a mark of more than forty centimeters. At a lower height, the drainage will not be controlled, and the equipment may simply break.
After setting up the electricity and water supply system, the appliances are inserted into the kitchen unit.
Once you have adjusted the level, use screws to screw the top of the dishwasher to the piece of furniture to secure it.
It will depend on the type of equipment (partially built-in or fully built-in) whether you need to fix the panel or hang a door that is used as a facade.
Then you can safely start the machine and expect high-quality results during its operation.
When you have bought furniture, and the decision to purchase a dishwasher has been made after that, choose the appliance carefully. To integrate equipment into a finished kitchen set, you need to take its measurements (width, height and depth).
In addition, it is also recommended to first find out exactly where you will place the device. You should check whether the machine door will open without obstacles. Install dishwashers as close to sewer outlets as possible to avoid overloading the system.
To ensure the safe use of electrical equipment, you can install an automatic plug on the panel as an additional measure. In case of energy fluctuations, it will turn off the device, which can protect it from possible combustion.
When installing decorative panels, check that they will not interfere with the movement of sliding elements. The area of the unit where you place the dishwasher will affect the distance between it and the communications. Pre-measure the required hose length and also measure it at the point of sale. Of course, if necessary, you can buy the hose separately (for example, if the factory part is not long enough).
Don't hesitate when purchasing a dishwasher. It will wash away greasy marks from dishes and will also save water consumption. Installing a dishwasher can be done even in a finished kitchen, and even if you want to do it yourself.
It would seem that just recently we did not think about any household appliances, except, perhaps, vacuum cleaners and ordinary washing machines, in which almost all operations had to be performed manually. However, today, many of us have already become very accustomed to comfort - automatic washing machines, washing vacuum cleaners, microwave ovens, food processors - jacks of all trades, smart refrigerators, etc. have appeared.
One of the most coveted appliances in the kitchen (though many won't openly admit it) is a little-known beast called a dishwasher. If someone you know has a dishwasher in their kitchen set, many behind their backs call such people “bourgeois,” and they themselves demonstrably declare that washing all the dishes by hand is not only easy, but also honorable.
In fact, of course, when people boldly shout out bravura statements about the correctness of washing dishes by hand, the overwhelming majority of them are simply lying, partly envying the lucky owners of dishwashers. And here, oddly enough, the financial side of the problem is not always in the foreground, especially since the prices for such equipment have dropped significantly and it has become affordable for a large number of people.
After all, when the owners are seriously talking about the advisability of purchasing such a device, first of all they discuss where to place the dishwasher in the kitchen. For many families, this becomes a real stumbling block - the living space is not so large that you can easily solve the question “where to put the dishwasher in the kitchen?” on these squares.
That is why the question immediately arises about what a dishwasher should be like. There are many models on the market now, so there is plenty to choose from. Manufacturers are trying their best to please all potential buyers, and their main concern is reducing the overall dimensions of equipment, while maintaining the same volume of loaded dishes and functionality.
Of course, it is also very important how this machine fits into the overall design of the room in which it will be used.
Naturally, the ideal option is one in which the dishwasher is purchased while renovation work is underway in the home. First, the owners decide where the car will be located and, depending on the decision made, decide what it will be like. If the machine stands alone, then certain requirements will automatically be imposed on it, in particular, its design will be very important. If the entire kitchen is designed in light colors, it will be somewhat strange to see a “dark spot” in the form of a dishwasher.
If the machine is located inside kitchen furniture, then its appearance is absolutely unimportant, and functionality and efficiency come to the fore. The location of the machine will greatly depend on the size of the kitchen. In many cases, corner kitchens with a dishwasher will be more than the right solution.
Actually, manufacturers have provided 3 options for devices, or rather, their facades:
In the case of placing a dishwasher inside a kitchen unit, you should immediately provide a kitchen cabinet for the dishwasher. In addition, you immediately need to carefully consider the entire communication system - the machine will need a water supply and sewerage. All pipes can be brought to the right place in advance; after the repair is completed, the machine will only need to be connected to them and start using it.
Everything will be much more complicated if the renovation was done a long time ago, a new one is not planned within the next 10 years, and the kitchen set did not imply the placement of a complex household appliance. There are not many options for solving this problem: the owners will either have to buy a new kitchen set, which will include space for a dishwasher, or improve what is available. Of course, this will be somewhat troublesome: the dishwasher in the kitchen unit must be placed and connected according to certain rules. That is, not only will it be necessary to install additional communication lines for it, but it will also have to be correctly and competently placed and installed.
If the owners decide to install a dishwasher on their own (especially since many would like to save money, and installation can greatly devastate the family budget), they should not neglect some useful tips regarding installation:
Before starting to operate the machine, of course, you should also carefully read the instructions, even for those people who “know everything” - it may contain very useful information on which safe and long-term cooperation with this useful device will depend.
interyerdizayn.ru
The problem is really serious. How to fit a stove with an oven, a refrigerator, a dishwasher, a microwave and a bunch of other appliances in a small kitchen, not counting the furniture? How to optimize space so that the kitchen can satisfy the needs of the family to the maximum? First, you need to sit in the kitchen and calmly, in silence, think about what solutions actually exist and are available at a given moment in time, and we will help you.
Compact dishwashers are called tabletop, because their weight and dimensions allow them to be placed directly on the table, somewhere in a corner.
Interested? Then let's look at these possible solutions in more detail. We hope our experience and our advice will really help you.
If there is nowhere to put the machine, then first of all you need to think about space planning. You might say that your space is too small to think about any kind of planning, but in fact, a sober look and careful calculations can work wonders. You need to make calculations in a room where even rough repairs have not yet been carried out, in order to take into account every little detail from the characteristics of the future floor covering to the location of sockets.
If you find it difficult to calculate the space of your own kitchen, invite a designer. He will charge some money for consulting services. But it will help you draw up an interior plan, according to which you will create your composition. One that the new dishwasher will seamlessly fit into. What should you pay attention to?
You can hang a microwave oven, bread maker or multicooker on the brackets.
In general, we want to tell you that a solution can always be found, the main thing is not to stop searching. Even a hopelessly small room can be turned into such a “candy” that it will fit not only a dishwasher, but also a washing machine.
You can save some space if you carefully select appliances for your kitchen. For example, a narrow built-in dishwasher can save as much as 15 cm, because unlike standard models, it is not 60 cm wide, but 45 cm. There are even models that do not reach 45 cm, so you can choose. We will not discuss the difference between a built-in and non-built-in dishwasher now, but will move on to more pressing issues. Let’s just say that for a small room, built-in models are always a priority.
It happens that literally 1 cm or even less is not enough to accommodate a narrow dishwasher. There is no other way to gain additional space, but there is a solution. You can remove sound insulation from the body of a built-in dishwasher. The equipment will be louder, but you will get the missing centimeter and solve the problem.
Thinking about how to place a dishwasher and refrigerator? Don't rack your brains, everything is obvious. You can’t give up a refrigerator and it’s better if it’s spacious, but you can give up the usual floor-mounted dishwasher in favor of a compact model. Tabletop dishwashers are a real godsend for those who have to live in cramped conditions. It can be placed on top of objects, such as a table, and it will work great there. However, you will have to endure some disadvantages:
Excessive noise is the “disease” of most compact dishwashers. It's difficult to get rid of, but if it doesn't bother you, then you don't have to bother.
Note that compact dishwashers are placed in cabinets suspended from the wall or attached with special durable brackets directly to the wall. In this case, the machine will not take up any useful space at all and will remain just as functional as if it were standing on the table. Compact models of dishwashers fit well into the sink under the sink. There they also do not interfere with anyone and function perfectly; moreover, there are no problems with connection, since all communications are nearby.
Strange name, isn't it? 3 in 1 appliances, what is it and what does a dishwasher and space saving in the kitchen have to do with it? In fact, the 3 in 1 technique is the solution to the problem. Let's give an example and everything will become clear to you. Candy TRIO 9503 is an electric stove with a glass-ceramic worktop, oven and dishwasher. Everything is combined in a compact package. There is a stove on top, an oven in the center, and a dishwasher at the very bottom, very convenient and, judging by the positive user reviews, practical.
What types of 3 in 1 equipment exist today? This technique does not differ in species diversity. Today on the market you can only find Candy TRIO products with electric and gas stoves; unfortunately, there are no other options. But this option is also quite acceptable. What are the disadvantages of 3 in 1 technology?
So, in a conceptual sense, we looked at how a dishwasher could be placed in a small kitchen. Perhaps some will say that our article lacks specifics, but the topic is quite abstract. If you could see before your eyes a specific kitchen into which you need to fit a dishwasher, then you could give specific advice. As it is, you have to make do with general recommendations, but in certain circumstances they can also turn out to be valuable. Ask specific questions in the comments to the article or on the forum, we will be happy to discuss this topic in more detail. Good luck!
mashmaster.ru
Many modern kitchens have a lot of built-in appliances - these include microwaves, washing machines, hobs, ovens, and of course dishwashers. This variety of equipment is explained by the fact that all economic life is concentrated in the kitchen. If everything is more or less clear with the rest of the equipment, then the dishwasher is a still unknown beast; not many kitchens can boast of such equipment. But if you have it, where should you build it in, how should you position it correctly? Which devices can be placed near and which cannot? Today I want to think about this issue, read the article - the location of the dishwasher in the kitchen......
Many people will not be interested in this article, because many budget kitchens do without dishwashers! As my mother said - Here's another! Why can't you wash dishes by hand? Maybe she’s right in some ways, but time dictates its own rules, and therefore “dishwashers” are gaining popularity here in Russia. It’s convenient to say - I put the dirty dishes in the dishwasher and took them out already dry, all that remains is to put them in the drawers.
BUT you know, the location of the dishwasher must be correct and convenient! I'll give you some advice. These tips are suitable for all types of machines, for those built into furniture (having facades matching the texture and color of the furniture on the front) and for non-built-in (external) dishwashers, those that do not have an external facade (regular white plastic or metal).
1) No need to install close to the stove or oven. This is bad for both the dishwasher and the stove-oven. During operation, the oven heats up and also heats nearby objects, albeit not much, since the oven has its own thermal insulation, but there is heating. And if the dishwasher is located nearby, then this heating will transfer to it. This heat can adversely affect the electronics and their rubber seals, which can lead to damage to the dishwasher. Therefore, many manufacturers recommend not placing a dishwasher and oven-stove next to each other. The minimum distance between them should be 15 cm, preferably 40 cm, or one narrow cabinet. That's exactly what I did.
2) Cannot be installed in the outermost drawer. At least, many manufacturers do not recommend such a mount. The “dishwasher” must be secured between two rigidly standing drawers, to which it must be secured and leveled. If you install the dishwasher from the edge, then one part will not be secured, which is not correct!
3) Also, when placing it, it is worth considering that you will need to get various powders and products for it, and therefore the “dishwasher” should be installed not far from the sink (as a rule, we keep all household utensils for the kitchen in the sink), approximately distance 80 – 100 cm.
4) Again, from the third point it is clear that you should not install the dishwasher far from the utensil drawers. It is logical to place the dishwasher next to or under the utensil drawer. It's just convenient, you don't have to stretch.
These are some simple tips. However, they are significant; place the dishwasher in the kitchen correctly to make it convenient and safe. That's all, read our construction site.
remo-blog.ru
Even the smallest space in modern apartments is filled with functional solutions designed to make life easier. Among such equipment, the dishwasher occupies a special place. However, not everyone and not always manage to find a convenient corner in the house for it, since kitchens rarely boast of space and freedom.
That is why the question of where to put a small dishwasher is very relevant. The most practical and functional option is the corner model. The photo clearly shows that this type of equipment can be fitted into that area of the apartment that is not occupied by anything else. This solution is very practical because the equipment:
It is optimal to think about purchasing and installing a dishwasher at the repair stage. If the device is purchased for a ready-made interior, then it is worth considering some of the subtleties of its location.
When determining where to put the dishwasher in a small kitchen, you need to take into account that it cannot be placed next to:
The thing is that these household appliances produce heat waves to one degree or another. They, in turn, negatively affect the functioning of the dishwasher. Heat can cause electronics and rubber seals to fail.
In small rooms, they often decide to place the dishwasher in the outermost compartment of the unit. This should not be done, as one of the sides will not be securely fixed. During the use of the unit, surges may occur, which in the future will lead to equipment failure.
So where to put a dishwasher in the kitchen if there is no free space? It is recommended to choose a corner cabinet that has all the walls. Fitting the device into such a ready-made furniture set will not be difficult. In this case, it is worth placing the device so that everything you need is at hand. Even a small room will be convenient if detergents are stored nearby and you don’t need to look for them every time in cabinets and shelves in the apartment.
Also, the space with the dishwasher will be functional and ergonomic if drawers with dishes and shelves for cutlery are placed near the household appliance. Carrying far away and laying out a lot of plates, forks, glasses is not only an inconvenient task, but also often dangerous, especially if there are small children and pets in the house.
The question of where to put the dishwasher if there is no space often becomes a real problem. If the room is very tiny and cramped, then you can always give preference to compact tabletop models. This solution is not demanding on the installation location and is perfect for a family of 2-3 people. Such devices are designed for 4-6 sets, which is quite convenient. If the floor option is placed, then for miniature rooms it is worth choosing practical narrow models.
When choosing any solution, it is important to consider the availability of communications. After all, constructing structures from many adapters is not only inconvenient, but also dangerous. That is why it is recommended to place this household appliance at the renovation stage in order to take into account all the subtleties of the space.
posudomoiki.vyborkuhni.ru
Not all people have the opportunity to do major renovations in the kitchen relatively often: change the kitchen set, redo the wiring, sewerage, pipes, and so on. But what to do if the kitchen is already done, you don’t particularly want to redo anything in it, but there is a need to purchase a dishwasher? Even if the kitchen is not small, it is impossible to find a place for new equipment “out of the gate,” especially equipment that requires connection to communications. How to integrate a dishwasher into a finished kitchen, this will be discussed in this story.
When we are just starting to plan the interior of the kitchen, and there is nothing in this room except shabby walls, it is much easier to determine where the dishwasher will be located. In our case, we already have a normally functioning kitchen, everything in it is in its place and there is nothing superfluous. How to integrate a new household appliance, and even a very large one, into such a room is an extremely important question that requires immediate resolution.
First, you should have an idea in your head where you could put this kitchen unit. As you understand, you will have to think very carefully, because there are not so many acceptable options. When thinking about the installation location, you must keep in mind the thought of connecting the dishwasher, because simply installing it is not enough, you need to ensure its normal operation, without any “technical extreme”. Experts offer several ideas on this matter.
Note! The dishwasher does not have to be placed on the floor; there are many design solutions when this machine was built into cabinets that hung from the floor at a height of 60-90 cm, or even higher.
Before you calculate whether a dishwasher will fit in a particular place, you need to decide what type of machine you want. There are the following types of “dishwashers”:
Fully built-in, small or partially built-in dishwashers fit best into a finished kitchen. You can read how to carry out calculations and successfully fit a built-in machine into the right place in the article Installing a built-in dishwasher. By the way, if you buy a compact dishwasher, you won’t have to look for a long place for it, because the dimensions of a small “dishwasher” are comparable to the dimensions of a microwave oven.
If you have a cabinet in your kitchen that can accommodate a dishwasher (it is the right size), then you need to properly adapt it for these purposes. By the way, not only standard floor cabinets with shelves are suitable. You can even build a dishwasher into a cabinet with pull-out drawers. What are we doing?
Important! If you don’t want to spend money on the front part or there are problems with its manufacture, you can return the doors back by first redoing the hinges on them.
What tools and materials are needed to install a “dishwasher” in a finished kitchen? We can only guess, because there are thousands of options. Basically, a standard set of tools is required, which are in every owner’s pantry., but with the components, not everything is clear.
The above list of materials is the main components, but you may also need a whole bunch of different little things: self-tapping screws, hidden hinges for doors, clamps, crimp couplings, etc. In general, be prepared to relate your ideas to the materials you have on hand or can easily buy.
Note! If you make a separate outlet for the dishwasher, get a two-core copper wire with good insulation and a moisture-resistant outlet.
The location has been chosen, the materials have been collected, ideas have appeared, we begin to connect the dishwasher. But where to connect it, because electrical and water communications were not specially prepared for a dishwasher. Let's start with electrics. The problem is that in a ready-made kitchen there is unlikely to be a separate outlet for a powerful consumer, and plugging the power cord into an existing outlet to which a refrigerator, microwave or other appliance is connected is highly not recommended. You can bring out a new outlet from the electric stove communications. 
This option for outputting the socket is not entirely correct, but we don’t have any special options. We cannot trench the walls for new wiring or screw in cable ducts, since the kitchen is already done. Now we will solve the issue with water and sewer communications, we will try to do this with little cost.
As you can see, there are no major alterations, everything is purely neat, but very effective. Now let's connect the dishwasher to the sewer. There is nothing special here - we install a pre-purchased siphon with an outlet for the drain hose. We connect to this outlet, not forgetting to make an elbow at the siphon and at the base of the “dishwasher”. Now all that remains is to put the dishwasher in place and carry out tests - the job is over.
To summarize, we note that if you do not know where to “plug” the dishwasher into an already completed kitchen, do not despair. Use your head, study the advice of experts and act. We have good reason to hope that everything will work out for you!
mashmaster.ru
Takes ~5 minutes to read
A dishwasher helps many housewives get rid of unloved work, while saving personal time. Having purchased furniture, the question arises: how to integrate a dishwasher into the countertop and is it possible to install it yourself?
The advantage of this technique is that the water consumption of a dishwasher becomes several times less, and with current utility rates this is very profitable. In addition, after a few years of operation, the cost of this unit will fully pay off.
Attention! An online 3D kitchen designer has launched on our website. You can get acquainted with it and design the kitchen of your dreams here completely free of charge!
Dishwashers are divided into three types: built-in, countertop and free-standing.
Before installing the machine, you need to find a suitable place for it. The main thing is that the water supply and sewage systems are located next to the equipment, and the heating system is further away, since exposure to heat can harm it. Typically, a built-in dishwasher is installed under the countertop. The device is manufactured with standard and non-standard types of fastening.
How to install a freestanding dishwasher under a countertop? We select the section where the equipment will be installed, remove the shelves and disassemble it. If necessary, you can use a screwdriver to move the mounting strips inside the box to another location.
A standard built-in dishwasher has a depth of 550 mm, a width from 450 to 600 mm, and a height of 820 mm. Simple instructions for installing the equipment yourself are included with each model. But you still need to know the basic rules:
Installation into a finished kitchen is a labor-intensive process. Not everyone knows all the intricacies and installation rules. But by doing the installation yourself, without involving a specialist, you can save money. The equipment installation instructions that come with each model will help you with this. The dishwasher is selected in accordance with the depth and width of the kitchen unit.
For installation you will need the following materials and tools:
The first thing to do is to ground the outlets in the apartment if they are not grounded. A specialist is called in for this work. Typically, in multi-storey buildings, the grounding wire is connected to a dead neutral line. You cannot connect the machine to a simple outlet, so another one is installed at a height of 250–350 mm from the floor. To connect equipment, only European sockets are used. They are equipped with a safety ground wire. Using a 16-amp circuit breaker, a socket for equipment is removed from the main contact connection.
To ensure that the electrical appliance is safe during operation and its warranty period does not expire, you cannot independently replace the standard plug on the cord with a different model.
Connecting the device to the water supply is easy. There are several ways to do this. The easiest and fastest option is to connect the tidal hose directly to the sink faucet in the kitchen. The disadvantage of this connection is that the faucet and hose look ugly in appearance and the faucet cannot be used while the machine is running. Despite the fact that this connection method is not very convenient, it can be used as a temporary one. The second option is more complex, but much better:
How is a dishwasher built into the kitchen if several devices are connected to the water supply (washing machine, filters and taps)? In this case, a collector should be installed. With one collector, the number of taps into the main pipe will be less.
Trying to save money, some consumers connect the dishwasher to the hot water system. You should not do this, since from 5 to 10 liters of water are consumed per one operating cycle of the machine, which is much more expensive. In addition, hot water can cause the check valve to break down, since it contains many different impurities.
To prevent the dishwasher from malfunctioning due to improper connection to the sewer, you need to know some subtleties. Sometimes, if the connection is incorrect, all the water from the machine goes down the drain and the equipment breaks down. Or unpleasant odors from the sewer get into the chamber of the device. To prevent all this from happening, you need to know how to connect the equipment correctly. There are two ways: installing a siphon or using an oblique tee.
When the connection work is completed, the machine must be leveled. The adjustable feet will help you adjust the position. Then, detergent is poured into the machine without loading dishes and a test run is carried out. The check will show:
In case of leaks, the nuts need to be tightened or additionally wrapped with FUM tape. If everything works well, the dishwasher is built into the furniture set. A decorative facade is installed on the machine door, which will hide the machine from the outside. The facade is attached according to the scheme indicated on the special templates included with the machine. A decorative door or panel is attached to the machine body with fasteners.
The dishwasher will last a long time and reliably without accidents, if you take into account some recommendations from experts:
diz-kitchen.ru
Hello, friends.
Buying a new dishwasher is a pleasant event, because the fleet of household appliances is replenished with another useful assistant.
However, before installation, you should carefully determine the place where it is best to locate it, and once again think about the state of all communications that will be required to ensure its operation.
Built-in full-size dishwashers are installed inside the kitchen unit. They can rest simply on the floor or on the base of the headset.
The support under the machine must be exactly horizontal and strong to prevent the machine from moving and damaging the body during operation, as well as to ensure compliance with technical standards, violation of which will void warranty repairs.
In most cases, built-in models involve mounting a furniture facade onto the machine door, which allows you to completely hide the appliance behind the facade or leave access to the top of the dishwasher, where the control panel is located.
Thus, the dishwasher will not be visible and will not disrupt the overall style of the interior.
You can often see dishwashers installed next to the oven and hob, but it is better not to place any other heating appliances next to them, although modern ovens emit minimal heat to the outside.
Perhaps the most important criterion for determining the installation location is proximity to power sources, water supply and drainage.
For household dishwashers and washing devices, this distance should not exceed 1.5 m. In other cases, when the distance is greater and the supply and drain hoses are extended, the machine will work with increased load on the motors, especially on the drain pump motor.
Particular attention should be paid to electrical wiring, since the addition of another powerful household appliance to the house can be critical. The outlet for the dishwasher needs to be separate and definitely grounded.
It may be necessary to install short-circuit circuit breakers.
The best connection option seems to be a direct connection to the electrical panel with the installation of a 16-amp switch.
If the house does not have any inconsistencies with the requirements for the communications supplying the dishwasher, the process of installing the machine is simple, and the installation instructions are very detailed for each model.
For installation you will need a ball valve, siphon, clamps, drill, pliers, screwdrivers, adjustable wrench and plumbing equipment installation skills.
Most dishwasher models are connected exclusively to a cold water supply, since heating must be carried out directly in the machine in accordance with the selected mode.
Any deviations from the set temperature will lead to failure of the dishwasher.
It is also important to ensure that the water supply to the machine is provided with a separate shut-off valve, which can be quickly turned off in the event of a leak in the dishwasher.
Typically the machine is connected to the sink drain by installing a tee.
When everything is installed, you should not immediately put the machine in place; you need to run it in test mode - without dishes, but with the addition of detergent, to make sure that the installation is reliable.
If everything is in order, you can slide the machine under the countertop, mount the front and enjoy getting rid of the tedious manual washing of dishes.
That's all, see you later.
Just recently, few people could afford to have a dishwasher, but progress does not stand still, household appliances are becoming more affordable. Now almost any family can afford to install a dishwasher in the kitchen.
But now another problem arises: usually the kitchen already has a kitchen unit. Then the question arises: how and where to install the dishwasher?
To complete the job you will need:
In order to install a dishwasher, you need to prepare a place for it; usually it is installed in one of the floor cabinets.
It is necessary to choose a cabinet whose dimensions allow you to easily install a dishwasher.
It is necessary to take into account that there is no more than 1.5 m from the specified device to the entrance to the sewer. Compliance with this condition ensures not only efficient, but also durable operation of the dishwasher, namely its evacuation pump. At the first stage of installation work, you need to select a cabinet and pull it out of the set. To do this, you need to unscrew the tabletop and unscrew the ties that connect it to the adjacent cabinets.
The cabinet must be disassembled, only the doors and side walls should remain in it, the back panel must be removed. It is necessary to make holes in the side wall; they are needed to connect the dishwasher to the water supply, sewerage and electrical wiring. To carry out this work, a drill with a crown of the required size is used.
Now you need to install the cabinet in place, insert the dishwasher into it and connect communications to it. During operation, namely when opening the dishwasher door, a lot of steam will come out, so that it does not render the countertop, walls and cabinet doors unusable, it is recommended to stick a special metallized mesh on them. To adjust the dishwasher, there are adjustable legs; it is recommended to lower them to the minimum height, only then install the machine horizontally.
Return to contents
You might be interested in: Connecting a kitchen faucet
In order to build in a dishwasher, first it is inserted into the prepared niche, then a hose and wires are inserted into the prepared holes and connected to the machine and communications. For the machine to be safe to use, it must be grounded, and to facilitate its maintenance, all hoses must be easily accessible. Installing an automatic device will allow you to turn off the device in time if it becomes overloaded or there is a network fault.
As with a washing machine, the drain hose of said household appliance must be located at least 40 cm from the floor. This is necessary so that during operation of the dishwasher there is no uncontrolled drainage of water, which can damage the device. Installing a water filter will increase the life of the machine.
When choosing a place to install this household appliance, you need to check that the door opens without interference. To avoid overloading the pump, it is necessary to install the dishwasher near the sewer outlet. If the length of the factory hoses is not enough, then you need to measure the required length and buy them separately.
Before you start using this household appliance regularly, you need to conduct a test run. It is not necessary to place dishes in it, but you must put detergent. This way, you will not only check the correct connection and tightness of all connections, but also clean the dishwasher.
https://site/youtu.be/U99aAeNEhNQ
When checking the operation of the device, you need to pay attention to such indicators as:
Return to contents
In order for the dishwasher to work efficiently and for a long time, it is necessary to operate it correctly: after completing the operating cycle, you need to open the door and let the appliance rest for a while. If your car does not have a system that warns of water leakage, then after washing it is necessary to turn off the water supply. If the machine is not in use, it is recommended to disconnect it from the network. To do this, you can turn off the machine or remove the plugs from the socket.
You might be interested in: How to install a gas stove in an apartment or house?
June 13, 2017Don't know where is the best place to install a dishwasher and how to do the job correctly? I will tell you about all the nuances of the optimal location of the equipment, and also describe all the intricacies of the installation process on my own.
To choose the best option for household appliances, you must know what types they come in. In addition, you need to determine in advance where the machine will be located, since both its size and installation options depend on this.
There are four main options for this technique:
To decide where to install your dishwasher, consider a few important tips:
| Illustration | Description |
 |
Do not place the dishwasher near other household appliances. The minimum distance from a gas stove or refrigerator should be at least 15 cm. Or better yet, make a space of 40 cm, that is, install any kitchen cabinet between the two elements. Close proximity negatively affects the electronics and reduces the service life of the seals. |
 |
It is better to place the structure between two cabinets. This is necessary to ensure that the fastening is strong on both sides. If you place the dishwasher in the outer cabinet, it will be firmly fixed on only one side, which is extremely undesirable.
|
 |
It is best to place the machine near the sink. This will greatly simplify the process of connecting equipment to the sewer; you will only need to buy a splitter to connect to the siphon or sewer outlet. At the same time, for a left-handed person it is better to place the equipment on the left, and for a right-handed person on the right, but this is a matter of comfort, not functionality. |
 |
Detergents should be on hand. The cabinet with household chemicals for the dishwasher should be located nearby, otherwise you will always have to go for products every time you turn on the equipment. |
 |
Provide proper placement of communications. Water supply, sewerage and electricity - without this, the operation of the equipment is impossible. The socket is located so that if you turn it off, you can easily reach it. The socket must be grounded - this is a prerequisite for the safe operation of electronics.
|
 |
The storage place for dishes should be nearby. It's best if the cabinet for plates and everything else is located above or to the side of the dishwasher so that you can put away clean items while standing still. This is a very important nuance that directly affects ease of use. |
Let's figure out how the equipment is installed. I will tell you how to install a dishwasher in a finished kitchen, as this is a more complex option. New furniture always has a compartment of the required size, while installation into an existing structure requires a number of additional works.
Instructions for doing the work yourself look like this:
| Illustration | Description of the stage |
 |
Equipment being unpacked. Before putting the machine back in place, you need to empty it from the packaging and carefully study the instructions. It will give basic installation recommendations that must be followed for quality work. |
 |
Space is freed up. You yourself must figure out how to dismantle the old cabinet. Sometimes it may be necessary to remove the countertop, but in our case we just needed to remove the doors. We already have an outlet, if you do not have one, then this should be done at this stage. In order not to rack my brains over how to integrate a dishwasher into a finished kitchen, so that the design would turn out neatly, it was decided to buy an open version. It does not need a facade, which simplifies installation. |
 |
Measurements are taken. The machine is bought according to the dimensions, but in order to set it accurately, you need to know the height of the opening to the nearest millimeter. |
 |
Legs are adjustable. Set the height so that there is only 3-4 millimeters between the tabletop and the equipment. |
 |
Holes are drilled if necessary. Both the water supply hose and the drain are pulled through them. The diameter and location depend on the size of communications and the equipment model. The exact position is determined by you. |
 |
Communications are being extended. The cable is connected to the outlet, and the machine is checked to turn on. If everything is fine, you can continue working. |
 |
All hoses are connected. For reliability, all joints are tightened with steel clamps. |
 |
The machine moves into place. Carefully place it in the opening and set it in the desired position. First check the plane with a building level and adjust the legs if necessary. |
 |
Attached to cabinets on the sides. The photo shows the locations of the fasteners; they are standard for all models. |
 |
This is what the result looks like. We figured out how a dishwasher is built into an existing kitchen; if you have new furniture, then everything will be even simpler, there will initially be an opening of the required size. |
You learned what types of dishwashers there are, how to choose the best location for them, and how to install them without assistance. The video in this article will explain the topic even better, and if you don’t understand something, ask in the comments.
A dishwasher is an excellent device that is becoming more and more popular every day. Just a few years ago, no one would have thought that a machine would appear that would be capable of washing dishes for a person. Today, many families have a similar unit. Today you don’t have to wait for the next renovation to install a dishwasher in your kitchen. This can be done in an existing room. You don't need to be a construction expert to do this. The entire instructions are quite simple.
Dishwasher diagram: 1 – switch, 2 – upper sprayer, 3 – lock, 4 – sprayer cover, 5 – pump cover, 6 – heating element, 7 – sprayer, 8 – power cable, 9 – float switch, 10 – motor, 11 – rubber door seal, 12 – drain hose, 13 – filling valve, 14 – filling hose, 15 – decorative panel.
Many people, when buying such a unit, think about how to integrate a dishwasher into an existing kitchen. This process will be described in detail below. It's not that difficult to build it in. First, it’s worth understanding what types of dishwashers currently exist.
Currently, there are three main types of dishwashers: external, partially built-in and built-in. The third type is the most widespread, as it allows you to save a huge amount of space in the kitchen.
You might be interested in: Correct connection of the kitchen sink
Now everyone knows about the main types of dishwashers. Now it’s worth talking more about how to integrate a dishwasher into a finished kitchen.
Return to contents
As with any other type of equipment, there are instructions for dishwashers that must be followed when working. You can install a dishwasher in the kitchen only by sequentially performing all the steps described in the instructions.
If you do not adhere to it, there is a high probability that a liquid leak will occur. This can lead to sad consequences and conflicts with neighbors. It is also important to connect the power supply correctly. Otherwise, the dishwasher may simply burn out due to a short circuit.
The instruction consists of several sequential actions. So, you can integrate a dishwasher into a finished kitchen as follows:
It is quite simple to integrate a dishwasher into the furniture in the kitchen. For this purpose, its design provides special holes and fastenings in the form of screws. They are screwed in using a screwdriver. In some cases, you can get by with a very ordinary screwdriver.
You might be interested in: How to connect a gas stove with a flexible hose?
Now it’s time to install the decorative panel and make a test run. During the test run, it is important to ensure that all connections are tight. If water does not leak out from anywhere, then you can load dishes into the dishwasher and enjoy its operation.
This is the method that can be used to integrate a dishwasher into the furniture in the kitchen.
Return to contents
If the set was purchased in advance, and it was decided to install a dishwasher later, then you should be extremely careful when choosing its specific model. It must fully comply with the geometric parameters that the set has.
It is worthwhile in advance, even before purchasing, to make all the necessary measurements using a tape measure. Only in this case can you choose a truly suitable model. Fortunately, the choice on the modern market is huge, so there should be no problems with the search.
It is worth considering in advance where the dishwasher will be installed. Its door should open fairly easily, and it should slide out without any hindrance. It is best to install the dishwasher as close to the sewer outlet as possible. In this case, the system will never be overloaded, and the drain will be done quickly enough.
As noted earlier, for emergency shutdown of the unit it is necessary to install a separate circuit breaker for the socket. The equipment is quite powerful, so it can overload the power supply system. If an individual machine is overloaded, it will simply turn off, and all other devices will continue to operate in normal mode. This measure also helps protect expensive equipment from short circuits. With our energy supply system, these phenomena can occur quite often.
Of course, everyone will install the decorative panel that comes standard with the car. It should be mounted in such a way as not to interfere with the exit of the internal part.
You might be interested in: Construction and installation of a single-lever kitchen faucet
https://site/youtu.be/Nl3i1il8ET8
It is worth considering the length of the hose that will be installed to provide the dishwasher with water. Long hoses are not always included in the standard package, so it is worth measuring the distance from the place where the machine will stand to where the water supply will be organized. If the standard length is not enough, then plumbing stores always sell similar devices.
You can buy a hose of almost any length.
