Stairs. Entry group. Materials. Doors. Locks. Design

Project name: Frame country house of one and a half floors Kremenki 2
House dimensions: 6.0 x 6.0 m
Total area of ​​the house: 72 sq.m
Construction period: 25 - 30 days

Frame country house 6x6 one and a half floors. Project of a 6x6 frame country house on one and a half floors, with a bathroom, kitchen-living room and recreation room on the ground floor. On the second floor there are two isolated living rooms - bedrooms.Plastic windows sizes 1.0x1.0, 0.5x0.5, 0.8x1.0

You can order additional services:

. Antiseptic treatment of the load-bearing frame
. Wiring, and installation
.Installation of a heating stove for wooden houses
. Exterior finishing with paint or varnish
. Redevelopment, adding partitions, windows
. Increasing ceiling heights
. Finishing the outside of the house with siding
. Extension of veranda, terrace
. Increasing window sizes

How to order to build a 6x6 frame house with one and a half floors:

Call us by phone and order free visit of a manager to conclude a contract. It is better to come immediately to the site to inspect the installation site of the house. You can make changes to the house design on the spot, fixing this in the contract, make an advance payment to the manager, and discuss the start and end dates of construction. If you do not have the opportunity to accommodate workers, we will bring a change house.

How can I pay for construction?Houses6x6 one and a half floors for a summer residence:

In cash
. Cashless payments
. Payment by raising funds

Advantages of a house with one and a half floors:

Frame house 6x6, one and a half floors more comfortable than a house with a classically shaped attic. When ordering a 6 by 6 one-and-a-half-story house, the customer receives a second floor of the same area as the first floor. This increases the usable area of ​​living rooms on the second floor.

Memo to the Customer:

To carry out work on the construction of a frame house, we need 220 volt light, access to water (well, well, imported), accommodation at the site (old house, bathhouse) or a change house. If it is not possible to provide a place for a team of workers to live, we will bring a construction shed.

• The foundation is support-column. 2 blocks per cabinet (for one-story houses) and 4 blocks per cabinet on a cement screed (for houses with an attic). Concrete blocks, solid, size 200x200x400 mm. The cabinets are installed on a compacted sand bed. Sand (PGS) is provided by the customer.
• An open terrace (if any) on supports made of planed timber with a cross-section of 100*150 mm, with shrinkage jacks. The fencing is a handrail made of planed timber with a cross-section of 40*100 mm. Steps at the entrance.
• Clear ceiling height of the first floor (from the floor joist to the floor beam) – 2.29 m (+/- 50 mm)
• The second floor is attic. Clear attic ceiling height (from floor beam to ceiling beam) – 2.25 m
• The gables are a frame made of natural moisture boards with a section of 150*40 mm, 100*40 mm. The external finishing of the gables is lining (spruce/pine AB) 17*90 mm. Wind protection – NANOIZOL “A” (for buildings with an attic).
• In the gables of one-story buildings, a door (1 piece) and ventilation hatches (1 piece for each gable, under the ridge) are installed.
• In the gables of buildings with an attic, ventilation hatches are installed (3 pieces for each gable).
• Eaves and roof overhangs with a width of 200 mm (for one-story buildings) and 300 mm (for buildings with an attic). The cornices and overhangs are hemmed with clapboard (spruce/pine AB) 17*90 mm.
• Construction of window and door openings with a dressing crown, without installing casing bars.
• Loading, delivery up to 400 km from the city of Pestovo, Novgorod region, unloading of a set of material.
• Assembly of a house/bath on the customer's site.

• The foundation is support-column. 2 blocks per cabinet (for one-story houses) and 4 blocks per cabinet on a cement screed (for houses with an attic). Concrete blocks, solid, size 200x200x400 mm. The cabinets are installed on a compacted sand bed. Sand (PGS) is provided by the customer.
• Waterproofing – roofing felt in one layer.
• The strapping is a beam of natural humidity with a cross-section of 150x100 mm. Along the outer perimeter the strapping is laid in two rows. The timber is treated with a protective compound.
• Floor joists - natural moisture board with a section of 40x150 mm per edge, with a pitch of 600 mm.
• The subfloor is a natural moisture board with a cross-section of 22x100mm. Steam, waterproofing – NANOIZOL S.
• Floor insulation – 100mm KNAUF/URSA mineral wool (or equivalent). Vapor barrier – NANOIZOL V.
• The finished floor of the first floor is a dry tongue-and-groove floorboard (spruce/pine AB) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• External walls - profiled timber of natural humidity with a section of 145x90 mm (wall thickness - 90mm) "block house" profile or straight. There are 17 crowns in total.
• The partitions of the first floor are profiled timber of natural humidity with a section of 145x90 mm, straight profile. They cut into external walls with a depth of up to 30mm.
• Inter-crown insulation – jute fabric 6mm thick
• Inter-crown connection - on a metal dowel (construction nail 6x200mm, 250mm).
• Corner connection - “half a tree”. The outer corners of the log house are covered with clapboard (spruce/pine AB) 17*90 mm in two rows.
• An open terrace (if any) on supports made of planed timber with a cross-section of 100*150 mm, with shrinkage jacks. The fencing is a handrail made of planed timber with a cross-section of 40*100 mm filled with carved balusters. Steps at the entrance.
• The terrace floors are dry tongue-and-groove floorboards (spruce/pine AB) 36mm thick. They are attached with self-tapping screws to each board. The boards are laid in 5 mm increments.
• The terrace ceilings are lining (spruce/pine AB) 17*90 mm. Vapor barrier – NANOIZOL V.
• Clear ceiling height of the first floor (from floor to ceiling) – 2.25m (+/- 50mm)
• The ceiling lining of the first floor is lining (spruce/pine AB) 12.8*88 mm. (joint for layout is allowed)
• The second floor is attic. Clear attic ceiling height (from floor to ceiling) – 2.20m
• The roof height at the ridge is 1.50 m (for one-story projects).
• Floor insulation – 100mm mineral wool KNAUF/URSA (or equivalent). Vapor barrier NANOIZOL V.
• The attic floors are dry tongue-and-groove floorboards (spruce/pine AB) 36mm thick. . Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• The cladding of the walls and ceiling of the attic is lining (spruce/pine AB) 12.5*88 mm (a joint for layout is allowed).
• Insulation of attic walls - 100mm basalt mats ROCKWOOL (or equivalent). Vapor barrier – NANOIZOL V.
• The attic partitions are a frame made of 40x75 bars, sheathed on both sides with clapboard (spruce/pine AB) 12.5*88 mm. The partitions are not insulated.
• Rafters - trusses made of natural moisture boards with a section of 150x40mm, 100x40mm. Installed in increments of 900-1000 mm.
• The gables are a frame made of natural moisture boards with a section of 150*40 mm, 100*40 mm. The external finishing of the gables is lining (spruce/pine AB) 17*90 mm. Wind protection – NANOIZOL “A” (for houses with an attic).
• In the gables of one-story houses, a door (1 piece) and ventilation hatches (1 piece for each gable, under the ridge) are installed.
• In the gables of houses with an attic, ventilation hatches are installed (3 pieces for each gable).
• The sheathing is a board of natural moisture with a cross-section of 22*100 mm, with a pitch of 300 mm. Counter-lattice - 20*40 mm slats, along the rafter slopes.
• Roof covering – ONDULIN (burgundy, brown, green) or galvanized corrugated sheeting. Under-roof vapor barrier – NANOIZOL S.
• Installation of a roof drainage system (PVC, DEKE). Colors – brown (chocolate), burgundy (pomegranate), white (ice cream).
• Eaves and roof overhangs are 200 mm wide (for one-story houses) and 300 mm (for houses with an attic). The cornices and overhangs are hemmed with clapboard (spruce/pine AB) 17*90 mm.
• The staircase to the attic is single-flight, on strings made of planed timber with a cross-section of 145*90 mm. Floorboard steps. The handrail and fencing in the attic are planed timber with a cross-section of 40*100 mm.
• The windows are wooden, double glazed, with sealing and fittings (screw-in hinges, twist locks). Inward opening doors. Dimensions (h*w) 1200*1500 mm; 1200*1000 m; 1200*600 mm; 600*600 mm. Windows are installed in casing boxes.
• Doors – wooden, paneled, solid (spruce/pine A). Size (h*w) 2000*800 mm; 2000*700 mm. Handles, hinges. A padlock is installed on the front door.
• Casing bars (swarms) are installed in window and door openings.
• Sealing corners, joints, abutments - spruce/pine plinth A.
• Finishing of windows and doors - spruce/pine frame A on both sides.
• Nails for fastening parts are black construction nails.
• Nails for fastening the lining – galvanized 2.5x50 mm
• Nails for fastening plinths, layouts - finishing galvanized 1.8x50 mm.
• Loading, delivery up to 400 km from Pestovo, Novgorod region, unloading of a set of material.
• Assembly of the house on the customer's site.

We have compiled for you a convenient table of differences in the configurations of houses for shrinkage and turnkey.

*-The indicated price includes materials, delivery within 400 km from our production and construction of a frame house by Russian carpenters.

• The strapping is timber of natural humidity (spruce/pine AB) with a cross-section of 150*100 mm. Along the outer perimeter the strapping is laid in two rows. The timber is treated with an antiseptic.
• Floor joists – natural moisture board (spruce/pine AB) with a section of 100x40 mm, with a pitch of 600 mm
• The subfloor is a board of natural humidity (spruce/pine AB) with a section of 19/22*100/150mm. Vapor and waterproofing – NANOIZOL S
• Floor insulation - KNAUF/URSA mineral wool, 50 mm thick. Vapor barrier - NANOIZOL "V".
• The finished floor of the first floor is a dry tongue-and-groove floorboard (pine B) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• External walls and gables - frame made of timber (pine B) with a section of 40x75mm. Assembly on construction, black nails.
• Insulation of walls and gables - ROKVUL basalt slabs, 50 mm thick. Vapor barrier - NANOIZOL V.
• Internal wall cladding - lining (pine B) 12.5*88mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• Partitions - frame made of bars with a section of 40x50mm. The cladding of the partitions is lining (pine B) 12.5*88 mm, along the racks.
• Clear ceiling height of the first floor (from floor to ceiling) - 2.20m
• Ceiling lining - lining (pine B) 12.5*88 mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• Floor insulation - KNAUF/URSA mineral wool, 50 mm thick. Vapor barrier - NANOIZOL V.
• The attic floors are dry tongue-and-groove floorboards (pine B) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• The cladding of the walls and ceiling of the attic is lining (pine B) 12.5*88mm. Sewn along the rafters through the Nanoizol V membrane.
• Insulation of attic walls - ROKVUL basalt slabs, 50 mm thick. Vapor barrier - NANOIZOL V.
• Attic partitions (if any) - frame made of bars with a section of 40x50mm. The cladding of the partitions is lining (pine B) 12.5*88 mm, along the racks.
• Rafters - trusses made of natural moisture timber (spruce/pine AB) with a cross-section of 40*100/150 mm. The rafters are installed in increments of 900 mm.
• Roof sheathing – natural moisture board (spruce/pine AB) 22/25*100/150mm. Counter grille – block 20*40 mm.
• Covering - profile sheets of galvanized steel. Under-roof vapor barrier - NANOIZOL S.
• The eaves and roof overhangs, 200 mm wide, are lined with clapboard (pine B) 17*90 mm.
• The staircase to the second floor (for houses with an attic) is on strings made of planed timber, with steps made of floorboards.
• Doors - wooden, paneled (pine B). Size 2000x800mm. Handles, hinges. Entrance door with padlock.
• Open terrace, porch (if provided for by the project). Supports - planed timber (spruce/pine AB) with a section of 100*100 mm. The fence is planed timber (spruce/pine AB) with a section of 40*100 mm in two belts. The floor is a dry tongue-and-groove floorboard (pine B) 36mm thick. They are attached with self-tapping screws to each board. The boards are laid in 5 mm increments. Ceiling - lining (pine B) 17*90 mm.
• Sealing of corners, joints, abutments - plinth (pine B) 40/45mm.
• Finishing of windows and doors - platband (pine B) on both sides.
• Delivery up to 400 km from our base in Pestovo, Novgorod region + unloading of the house kit. (https://yandex.ru/maps/10920/pestovo/?ll=35.809228%2C58.596895&mode=search&oid=1081678118&ol=biz&z=17)

• The foundation is support-column. 4 blocks 200x200x400 in a cabinet on a cement screed. The cabinets are installed on a compacted sand bed. Sand (or ASG) is provided by the customer.
• Waterproofing - roofing felt in one layer.
• Floor joists - natural moisture board (spruce/pine AB) with a section of 150x40 mm, with a pitch of 600 mm, treated with an antiseptic.
• The subfloor is an edged board of natural moisture (spruce/pine AB) with a cross-section of 19/22*100/150mm, treated with an antiseptic. Vapor and waterproofing – NANOIZOL S.
• Floor insulation - min. KNAUF/URSA cotton wool 100 mm thick. Vapor barrier - NANOIZOL "V".
• The finished floor of the first floor is a dry tongue-and-groove floorboard (spruce/pine AB) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• External walls and gables - frame made of natural moisture timber (spruce/pine AB) with a cross-section of 40x100mm. The frame is treated with the fire-bioprotective composition NEOMID.
• External cladding of walls and gables - 9mm OSB panels, moisture resistant. Wind and moisture protection - NANOIZOL A.
• Internal wall cladding - lining (spruce/pine AB) 12.5*88mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• Partitions – frame made of natural moisture timber (spruce/pine AB) with a cross-section of 40x75mm. The frame of the partitions is treated with the fire-bioprotective composition NEOMID.
• Sheathing of partitions - lining (spruce/pine AB) 12.5*88 mm, along racks.
• Clear ceiling height of the first floor (from floor to ceiling) - 2.30m
• Ceiling lining - lining (spruce/pine AB) 12.5*88 mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• The second floor is an attic (if provided for by the project). Clear attic ceiling height (from floor to ceiling) - 2.20m
• The roof height at the ridge is 1.50 m (for one-story projects).
• Insulation and sound insulation of floors - min. KNAUF/URSA cotton wool, 100 mm thick. Vapor barrier - NANOIZOL V.
• The attic floors are dry tongue-and-groove floorboards (spruce/pine AB) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• The cladding of the walls and ceiling of the attic is lining (spruce/pine AB) 12.5*88mm. Sewn along the rafters through the Nanoizol V membrane.
• Attic partitions (if any) - frame made of natural moisture timber (spruce/pine AB) with a cross-section of 40x75mm. The frame of the partitions is treated with the fire-bioprotective composition NEOMID.
• The partitions are covered with lining (spruce/pine AB) with a cross-section of 12.5*88 mm, along racks.
• Rafters - trusses made of boards of natural moisture (spruce/pine AB) with a cross-section of 40*100/150 mm. The rafters are installed in increments of 800 mm.
• Roof sheathing – natural moisture board (spruce/pine AB) 22/25*100/150mm. Counter-lattice – block 20*40 mm
• All wooden roof elements are treated with fire-bioprotective composition NEOMID.
• Covering - steel profile sheets with polymer coating. Colors to choose from: RAL3005 “wine red”; RAL6005 moss green; RAL8017 “chocolate” RAL7004 “gray”; RAL5005 "blue". Under-roof vapor barrier - NANOIZOL S.
• The staircase to the second floor is made of planed timber, with wide steps. Railings and fencing in the attic made of planed timber 40*100 mm.
• The windows are wooden. Double glazing. Inward opening doors. Screw-in hinges, twist locks. Dimensions (height*width): 1200*600/1000/1200/1500mm; 600*600 mm.
• Interior doors - wooden, paneled, polished (spruce/pine AB). Size 2000x800mm. Handles, hinges.
• Entrance door - steel, insulated STANDARD.
• Open terrace, porch (if provided for by the project). Supports - planed timber (spruce/pine AB) with a section of 100*100 mm. The fencing is planed timber (spruce/pine AB) with a cross-section of 40*100 mm filled with carved balusters. The floor is a dry tongue-and-groove floorboard (spruce/pine AB) 36mm thick. They are attached with self-tapping screws to each board. The boards are laid in 5 mm increments. Ceiling - lining (spruce/pine AB) 17*90 mm.
• Sealing of corners, joints, abutments - plinth (spruce/pine AB) 40/45mm.
• Finishing of windows and doors - platband (spruce/pine AB) on both sides.
• Hardware: black construction nails, galvanized construction and finishing nails, self-tapping screws.
• Delivery up to 400 km from our base + unloading of the house kit.
• https://yandex.ru/maps/10920/pestovo/?ll=35.809228%2C58.596895&mode=routes&oid=1081678118&ol=biz&rtext=58.596895%2C35.809228&rtt=auto&z=17
• Assembly of the house on the customer's site.

• The foundation is support-column. 4 blocks 200x200x400 in a cabinet on a cement screed. The cabinets are installed on a compacted sand bed. Sand (or ASG) is provided by the customer.
• Waterproofing - roofing felt in one layer.
• The strapping is timber of natural humidity (spruce/pine AB) with a cross-section of 150*150 mm. Along the outer perimeter the strapping is laid in two rows. The timber is treated with a protective compound.
• Zabirka is a decorative finishing of the base. Frame made of timber 40*100 mm with sheathing made of boards 22*100 mm. Flooring - profile steel sheets with a polymer coating in the color of the roof. The ebb along the perimeter of the foundation from the upper edge of the trim. Ventilation openings (vents).
• Floor joists - chamber-drying board (spruce/pine AB) with a section of 150x40 mm, with a pitch of 600 mm.
• The subfloor is a chamber-dried edged board (spruce/pine AB) with a section of 19/22*100/150mm. Vapor and waterproofing - NANOIZOL S.
• The piping, joists and subfloor are treated with the protective non-washable composition NEOMID.
• Floor insulation – min. Knauf cotton wool, 150 mm thick. Vapor barrier - NANOIZOL "V".
• The finished floor of the first floor is a dry tongue-and-groove floorboard (spruce/pine A) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• External walls and gables - frame made of chamber-dried timber (spruce/pine AB) with a cross-section of 40x100mm. Assembly on nails using galvanized steel perforated fasteners.
• External cladding of walls and gables - 9mm OSB panels, moisture resistant. Wind and moisture protection - NANOIZOL A. The joints of the panels are closed with slats.
• Insulation of walls and gables - ROKVUL basalt slabs, 100 mm thick. Vapor barrier - NANOIZOL V.
• Internal wall cladding - lining (spruce/pine A) 12.5*88mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• Partitions - frame made of chamber-dried timber (spruce/pine AB) with a cross-section of 40x100mm. Insulation and sound insulation of partitions - ROKVUL basalt slabs 100 mm thick.
• The partitions are covered with lining (spruce/pine AB) 12.5*88 mm, along the racks through the NANOIZOL V membrane.
• Clear ceiling height of the first floor (from floor to ceiling) - 2.40m
• Ceiling lining - lining (spruce/pine A) 12.5*88 mm. Counter rail - 10*30 mm. Ventilation gap - 10 mm.
• The second floor is an attic (if provided for by the project). Clear attic ceiling height (from floor to ceiling) - 2.25m
• The roof height at the ridge is 1.50 m (for one-story projects).
• Floor insulation – min. Knauf cotton wool, 100 mm thick. Vapor barrier - NANOIZOL V.
• The attic floors are dry tongue-and-groove floorboards (spruce/pine A) 36mm thick. Every fifth board is fastened with self-tapping screws (for the possibility of re-upholstering the floors in the future).
• The cladding of the walls and ceiling of the attic is lining (spruce/pine A) 12.5*88mm. Sewn along the rafters through the NANOIZOL V membrane.
• Attic ceiling insulation – min. Knauf cotton wool, 100 mm thick. Vapor barrier – NANOIZOL V
• Insulation of attic walls - ROKVUL basalt slabs, 100 mm thick. Vapor barrier - NANOIZOL V.
• Attic partitions (if provided for by the project) - frame made of chamber-dried timber (spruce/pine AB) with a cross-section of 40x100mm. Insulation and sound insulation of partitions - ROKVUL basalt slabs 100 mm thick.
• The partitions are covered with lining (spruce/pine A) 12.5*88 mm, along the racks through the NANOIZOL V membrane.
• Rafters - trusses made of chamber-dried boards (spruce/pine AB) with a cross-section of 40*100/150 mm. The rafters are installed in increments of 600 mm.
• Roof sheathing - chamber drying board (spruce/pine AB) 22/25*100/150mm. Counter grille - block 20*40 mm.
• Covering - metal tiles. Colors to choose from: RAL3005 “wine red”; RAL6005 moss green; RAL8017 “chocolate”; RAL7004 grey; RAL5005 "blue". Under-roof vapor barrier - NANOIZOL S.
• Installation of a roof drainage system (PVC Dyoke).
• The eaves and roof overhangs, 300 mm wide, are lined with clapboard (spruce/pine AB) 17*90 mm.
• The staircase to the second floor (for houses with an attic) is on strings made of laminated veneer lumber, with wide steps. Turned posts and balusters. Figured handrail and fencing in the attic.
• Windows - PVC, white with single-chamber double-glazed windows. Dimensions (height*width): 1200*600/1000/1200/1500mm; 600*600 mm.
• Interior doors - wooden, paneled, polished (spruce/pine A). Size 2000x800mm. Handles, hinges.
• Windows and doors are installed in mounting boxes. Technological gaps are filled with polyurethane foam.
• Entrance door - steel, insulated, PRESTIGE. Size 2050*870 mm.
• Open terrace, porch (if provided for by the project). Supports - chamber-dried planed timber (spruce/pine AB) with a cross-section of 100*100 mm. The fencing is chamber-dried planed timber (spruce/pine AB) with a cross-section of 40*100 mm filled with carved balusters. The floor is a dry tongue-and-groove floorboard (spruce/pine A) 36mm thick. They are attached with self-tapping screws to each board. The boards are laid in 5 mm increments. Ceiling - lining (spruce/pine A) 17*90 mm.
• The entire building is treated externally and internally with the fire-retardant composition NEOMID. Including: external walls and gables, internal walls, floors, ceilings, hidden elements of the roof's load-bearing structure (rafters, sheathing, counter-lattice).
• Sealing of corners, joints, abutments - plinth (spruce/pine A) 40/45mm.
• Finishing of windows and doors - platband (spruce/pine A) on both sides.
• Hardware: black construction nails, galvanized construction and finishing nails, self-tapping screws, perforated galvanized fasteners.
• Delivery up to 400 km from our base in Pestovo, Novgorod region + unloading of the house kit. https://yandex.ru/maps/10920/pestovo/?ll=35.809228%2C58.596895&mode=routes&oid=1081678118&ol=biz&rtext="&rtt=auto&"amp;z=17
• Assembly of the house on the customer's site.