Vacuum valves
A vacuum valve or sewer aerator is used in systems internal sewerage to prevent entry into the room unpleasant odors, harmful gases and vapors from the system, as well as to relieve pressure in the system. Vacuum valve 110 (aerator 110) is installed on top of vertical risers in the sewerage system in attic spaces, toilets, bathrooms, etc., where uninterrupted flow to the valve will be ensured fresh air.
Also, a vacuum valve is used for local aeration of sinks, bidets, toilets, where a large flow of waste liquid can lead to the creation of air vacuum (suction of water from the siphon water seal), in this case, as a rule, a vacuum valve 50 is used.
Stubs
Designed to close unused socket connections of sewer pipelines.
Umbrellas
The sewer ventilation hood is designed to protect sewer risers leading to the roof of a building.
Crosspieces
The single-plane cross is designed to connect additional branches to the pipeline in one plane. The two-plane crosspiece is designed to connect additional branches to the pipeline in two planes.
Double socket couplings
The double-socket coupling is used for installation of non-pressure sewer pipes wires internal systems sewerage of buildings and structures for various purposes. The coupling has a double-socket design and is designed to make pipe connections on both sides, thanks to the jumper on inner surface couplings.
Check valve
A sewer return valve is installed at points of entry into the general sewer system to prevent backflow Wastewater with the possibility of using forced blocking.
Bends
Used to change the direction of pipe laying during installation. Thanks to sewer outlets, you can turn the pipe in any direction. This is especially useful when complex piping systems are being installed and it is necessary to go around a corner or architectural protrusion.
Bends 110 with output 50
Used to create bends and bends, as well as connections additional elements and plumbing installations and sewer communications.
Compensation pipes
Used to compensate for construction tolerances.
Transitions to cast iron
Used for transition from bell polypropylene pipe to the smooth end cast iron pipe. For a tight connection, a special rubber cuff is required.
Eccentric transitions
Designed to reduce flow and connect the socket of a sewer pipe/fitting of a larger diameter with the smooth end of a pipe/fitting of a smaller diameter.
Connection to the toilet
Toilet connections are designed to connect the toilet to the sewerage system. Mainly used for horizontal connection method.
Audit
Designed for cleaning sewer pipes.
Tees
Designed to connect an additional branch to the pipeline D110, D50, D40 and D32 at different angles
Clamps
Used to fix system elements, the distance between the clamps should be: for horizontal lines - 10 diameters of the pipe being laid, for vertical lines (for risers) - 1000-2000 mm
Company " Truba-Plast» offers expansion pipes PP at competitive prices in Moscow. They are used in gravity pipelines internal networks sewerage of administrative, industrial and residential buildings and structures.
Main characteristics of the pipes:
Products comply with domestic GOST and international technical standards. Products can be delivered to any region of Russia.
Expansion pipes made of PP polypropylene are necessary to compensate for construction tolerances and simplify installation and assembly work. Recommended for use at the bottom of risers in technical rooms. The presence of a branch pipe allows you to avoid deformation and destruction of pipelines, and makes it possible to remove damaged network elements without disassembling it.
Thanks to the bell-shaped design, the pipes are easy to install. They are equipped with a rubber sealing ring, which ensures high tightness and reliability of the connection. Additional qualities: resistance to corrosion, aggressive environments. Can function normally at both high and low temperatures.
PP compensation pipe DN 110 mm sewer PVC internal single-socket sliding PP D 110 mm for internal sewerage
Fasonant part for connection sewer PVC pipes and shaped parts without socket joints. The thrust flange in the coupling design provides correct installation pipes and fittings. PVC fittings provide a tight, hermetically sealed connection of sewer pipes. The sockets have a high-quality rubber seal that is resistant to aggressive environments.
Compensation pipe for internal sewerage- gray polypropylene sewer fitting. It is intended for repairing the intra-house sewerage network in both residential and non-residential buildings and premises.
Sewer compensation pipe has a long service life (at least fifty years). The standard diameters of this fitting coincide with the standard diameters of gray sewer pipes and are 5 and 11 centimeters.
Vacuum valves
A vacuum valve or sewer aerator is used in internal sewage systems to prevent unpleasant odors, harmful gases and vapors from the system from entering the room, as well as to relieve pressure in the system. Vacuum valve 110 (aerator 110) is installed on top of vertical risers in the sewerage system in attics, toilets, bathrooms, etc., where an uninterrupted supply of fresh air will be ensured to the valve.
Also, a vacuum valve is used for local aeration of sinks, bidets, toilets, where a large flow of waste liquid can lead to the creation of air vacuum (suction of water from the siphon water seal), in this case, as a rule, a vacuum valve 50 is used.
Stubs
Designed to close unused socket connections of sewer pipelines.
Umbrellas
The sewer ventilation hood is designed to protect sewer risers leading to the roof of a building.
Crosspieces
The single-plane cross is designed to connect additional branches to the pipeline in one plane. The two-plane crosspiece is designed to connect additional branches to the pipeline in two planes.
Double socket couplings
The double-socket coupling is used for installation of non-pressure sewer pipelines internal sewerage systems of buildings and structures for various purposes. The coupling has a double-socket design and is designed to make pipe connections on both sides, thanks to a jumper on the inner surface of the coupling.
Check valve
A sewer return valve is installed at the points of entry into the general sewer system to prevent the reverse flow of wastewater with the possibility of using forced blocking.
Bends
Used to change the direction of pipe laying during installation. Thanks to sewer outlets, you can turn the pipe in any direction. This is especially useful when complex piping systems are being installed and it is necessary to go around a corner or architectural protrusion.
Bends 110 with output 50
Used to create branches and bends, as well as connect additional elements and plumbing devices for sewer communications.
Compensation pipes
Used to compensate for construction tolerances.
Transitions to cast iron
Used for transition from the socket of a polypropylene pipe to the smooth end of a cast iron pipe. For a tight connection, a special rubber cuff is required.
Eccentric transitions
Designed to reduce flow and connect the socket of a sewer pipe/fitting of a larger diameter with the smooth end of a pipe/fitting of a smaller diameter.
Connection to the toilet
Toilet connections are designed to connect the toilet to the sewerage system. Mainly used for horizontal connection method.
Audit
Designed for cleaning sewer pipes.
Tees
Designed to connect an additional branch to the pipeline D110, D50, D40 and D32 at different angles
Clamps
Used to fix system elements, the distance between the clamps should be: for horizontal lines - 10 diameters of the pipe being laid, for vertical lines (for risers) - 1000-2000 mm
Compensation pipe 110 mm used as a connecting fitting when installing non-pressure water pipelines of the appropriate diameter. Its task is to compensate for construction tolerances and deformation loads that can destroy PP pipes. Since standard construction allows a difference of several centimeters, the expansion pipe DN 110 can significantly simplify installation work.
Functions of the polypropylene expansion pipe:
simple repair of damaged sections of polypropylene pipes;
compensation of construction tolerances and axial displacements;
compensation for thermal expansion and deformation.
In Moscow, the greatest demand is for inexpensive plastic pipes from the RosTurPlast company from Russia, as well as products from the German manufacturer Ostendorf, the price of which is justified by more than high quality. You can buy original fittings from these brands in the Santekhkomplekt online store. In addition to conventional products of different lengths, noise-reducing and flexible pipes are also available.
