Compound
Dry mixture based on high-quality special cements, fractionated aggregates, water-repellent and modifying additives.
Application
Waterproofing of building foundations, facades, plinths, basements, balconies, terraces, as well as walls and floors in any premises with possible water ingress. For interior and exterior use.
Base requirements
Concrete, brickwork, cement strainer, cement plaster. The age of cement-sand foundations is at least 28 days, brick and concrete foundations- at least 3 months.
The base must be dry and durable. Before applying Aquastop, it is necessary to remove from the surface weak and loose layers, oil stains and other contaminants that interfere with the adhesion of the waterproofing to the base. Clean out seams and cracks, deepen them by 1-2 cm and fill with appropriate material. Significant unevenness must first be leveled using appropriate materials. On internal corners make roundings (fillets, fillets) with a radius of at least 3 cm, make chamfers at the outer corners at an angle of 45°. Before applying Aquastop coating waterproofing, the base should be moistened abundantly.
The prepared solution is applied with a brush or spatula. Mortar mixture Apply in 2 or 3 passes with a layer of uniform thickness. It is recommended to apply the first layer with a brush. The following layers are applied in cross directions with a brush or spatula onto the hardened but still wet previous layer. The fillets and chamfers in the corners are carefully processed during the application of the first layer.
During work and in the next two days, the temperature of the air and the surface of the base should not be lower than +5 °C and not higher than +30 °C. During the first day of hardening, the waterproofing layer must be maintained wet, protect it from exposure to precipitation, direct sun rays and freezing. Applying subsequent coatings, creating a screed, plastering and gluing tiles is possible no earlier than 3 days after installing the waterproofing.
Paper bag 20 kg
Waterproofing AQUASTOP (20 kg) – RUB 34.00/kg
Waterproofing AQUASTOP (20 kg) – RUB 680.00/bag
Sometimes the circumstances do not allow necessary work on external waterproofing of building structure surfaces. This may apply to both old buildings and new buildings in which the waterproofing materials used during construction have been destroyed, if any were used by the developer at all. Internal waterproofing, for which various materials are available, can correct the situation. However, the most effective is considered to be Aquastop waterproofing, which includes three different material, used both individually and together in the system. Using this technology, it is possible to quickly stop the destruction construction structures from exposure to moisture coming from outside. Therefore, it is not surprising that Aquastop waterproofing, tested with success at many facilities, is considered a popular material in construction market.
The Aquastop waterproofing system differs from other similar materials in a number of advantages, namely:
Autostop waterproofing system
For application work internal waterproofing according to the unique Aquastop system, it is necessary to prepare the base by eliminating possible leaks using a special fixer called Puder-Ex. This material is produced in the form of a powder that can quickly harden upon initial contact with water. At the same time, the material has excellent adhesion to concrete surfaces, as well as brick and stone masonry. After curing within a few seconds, the fixative becomes:
Before use, powdered powder is not mixed with water. Squeeze a lump of dry powder in your palms for a few seconds, and then quickly apply it to the breakout site and hold the fixative with your hand for ten seconds. The material gets wet and hardens, firmly adhering to the surface being treated. If the breakthrough has large area and it cannot be closed in one go, then the procedures are repeated many times. At the same time, each time the leak site narrows and then is completely eliminated. “Weeping” surfaces, covered with leaked droplets of water, are treated with powder rubbed into them with the back of the hand. In this case, the movements should be directed up and down.
Important! When performing this work, the worker must protect his hands by wearing smooth rubber gloves.
Unique powder in the form tiny particles powder allows you to eliminate water breakthrough in a matter of seconds
In concrete and iron concrete structures When preparing the base for applying Aquastop waterproofing, all existing technological and expansion joints are jointed, followed by the installation of waterproofing dowels produced by the same manufacturer. In the manufacture of waterproofing dowels, dense rubber is used, the base of which is ethylene propylene rubber. Dowels are recommended for use when waterproofing joints in concrete structures of basements and underground garages, as well as when protecting building foundations from moisture.
AQUASTOP dowels are intended for installation and restoration of waterproofing of expansion and technological concreting joints in reinforced concrete structures underground and buried structures
A solution of special slurry is applied to the prepared base with a brush, creating the first sealing layer in this system. If the base is dry, then it must be moistened with water. Special sludge is produced in the form of a cement-based powder containing inorganic reagents. The powder is mixed in water and quickly mixed by hand until a plastic and homogeneous consistency is formed. The resulting mixture is applied at a temperature of 5-30 °C.
Important! The mixture must be diluted in small quantity, since its viability is too low. Remember that a trained worker can treat no more than two with waterproofing material in one go. square meters surfaces.
At the second stage, fixative powder is immediately rubbed into the freshly applied solution, while maintaining the same temperature regime.
The third step is to apply an insulating silica compound to the previous layer of Puder-Ex sealant. The work is carried out with a brush or brush. The insulating silicicate does not contain solvents and allows for compaction of small pores remaining in previously applied waterproofing materials.
At the fourth stage, the silicicate layer is covered without the slightest delay with an additional, second layer of special sludge. This time this material acts as a sealing layer. After applying the slurry, a technical break is taken for 15-20 minutes, during which the layer dries.
Step-by-step application of Aquastop waterproofing allows you to build a high-quality waterproofing barrier on any building structures
At the last stage, the third layer of sludge is applied, which is necessary for subsequent plastering of walls and ceilings, as well as laying floor screed.
Important! As a result of performing all five stages of work, a reliable waterproofing coating is obtained, the thickness of which does not exceed three millimeters. TO the following types work begins a day later.
Aquastop system - waterproofing highest level quality. When working with materials included in this system, experience and skill are required. Therefore, to perform waterproofing works It is better to invite professionals with the necessary qualifications.
Protection of a balcony or loggia from moisture penetration can be achieved using various modern methods. The choice of waterproofing depends on the conditions of use and, of course, the material of the structure that needs protection. Universal waterproofing Aquastop, being an advanced product on the construction market, will allow you to approach waterproofing issues in a comprehensive manner. According to professionals, this system has no analogues.
This is a specific material used to obtain a reliable and durable water-repellent coating. Aquastop is used for finishing different reasons: from brick, concrete, plaster, cement, aerated concrete, gypsum and other materials. This type of waterproofing can be used for priming porous surfaces and moisture-sensitive materials.
Aquastop is a universal product line containing a set of high-quality water-dispersion primers that protect the room from moisture. A similar task is relevant for finishing a balcony or loggia with insulation. To provide a room with comprehensive water protection, it is necessary to use 3 types of dry mixture, each of which does its own job:
Tip: If you need to seal the seams between panels, as well as the wall and foundation, use a unique waterproofing dowel Aquastop. Made from high-strength rubber, it also effectively holds a large influx of water.
Scope of application Aquastop: internal and exterior decoration residential, office and production premises; used, kitchen area and the bathroom, laundry room and other rooms that have a fairly high degree of humidity.
Concentrated coating waterproofing Aquastop Coating rigid waterproofing mixture based on cement, fractionated sand and hydrophobic polymer, for the protection of basements, ground floors, swimming pools, bathrooms, blind areas, foundations, etc. from water penetration.
The base on which the waterproofing coating is applied is cleaned of dust and dirt, loose particles, oil, paints, etc. manually or mechanically (using high-pressure water, sandblasting). Defective concrete is healed with a repair compound. The prepared base must be moistened before applying the main coating.
Pour the mixture into a container with clean water(at the rate of 6.0-6.5 liters of water per 25 kg of mixture) and mix mechanized way until smooth (about 2-3 minutes). Let the solution sit for 2 minutes, then stir for 1-2 minutes.
The prepared portion of the solution is used for its intended purpose within 40 minutes (after adding the mixture to the water). If the solution loses its mobility, it is permissible to re-mix without adding water.
The prepared solution is applied to the prepared surface to be treated using a hard brush, brush, spatula or appropriate spray equipment in one layer. If necessary, apply a second layer, strictly in a perpendicular direction, while the first is still “fresh”. During the entire hardening period, the freshly applied solution must be protected from direct sunlight, rain, wind, etc. Mixture consumption: About 4-5 kg/m2 when applied in two layers with a total thickness of 2-3 mm.
Kraft paper bags 25 kg. The shelf life in a dry place and original packaging is 12 months from the production date indicated on the packaging.
Do not let the dry mixture get into your eyes. In case of contact, rinse the affected area thoroughly. running water, if necessary, consult a doctor. Wear goggles and protective clothing when working.
Waterproofing Aquastop Perfekta (Perfecta)- This mortar to create a hard waterproof coating (waterproofing layer) on various substrates; used for building foundations, facades, plinths, basements, balconies, terraces.
The coating is highly waterproof and waterproof, withstands high mechanical loads, and is resistant to alkali salts. We especially note that the price of Aquastop is quite affordable compared to competitive brands.
The material is used for waterproofing building foundations, facades, plinths, basements, balconies, terraces, indoor pools, water tanks, walls and floors in wet areas. The material is designed to create a hard, waterproof coating. You can only buy waterproofing at a competitive price from an official partner.
Perfekta Aquastop waterproofing is easy to apply. This is done using one of the tools: a brush, trowel or spatula on bases whose temperature is in the range from +5 to +30 degrees.
If you decide to work with a brush, then for the desired effect the waterproofing mixture is applied in three layers, with each layer applied at an angle of 90 degrees to the previous one. Each subsequent layer is applied after approximately eighteen hours. The thickness of the coating should be about 3-4 mm.
If it is more convenient for you to work with a trowel or spatula, then you can apply the waterproofing mixture in two layers, and it is recommended to apply the first layer with a brush.
In addition, in order to achieve greater water resistance, it is best to apply Aquastop with a spatula (or trowel), in this case the indicator will reach the W20 level, which means the ability to withstand water pressure of 20 atmospheres.
When applying the waterproofing mixture with a brush, the waterproof rating will not exceed level W8 (8 atmospheres).
Subsequent work, such as plastering, laying tiles or porcelain stoneware, creating self-leveling floors, screeds, is recommended to be carried out no earlier than three days later. At the same time, for three days it is necessary to avoid exposure of the applied waterproofing (waterproofing mixture) to direct sunlight, natural precipitation and exposure to low temperatures (frost).
The average consumption of Perfekta Aquastop dry mixture is about 4 kg per 1 sq.m.
