Geberit impuls 240 drain valve how to set up. How to install a Geberit installation yourself. Installation of frame installation

Stairs. Entry group. Materials. Doors. Locks. Design » Insulation Geberit impuls 240 drain valve how to set up. How to install a Geberit installation yourself. Installation of frame installation

Geberit impuls 240 drain valve how to set up. How to install a Geberit installation yourself. Installation of frame installation

The Swiss company Geberit has been successfully manufacturing and selling various sanitary equipment for many years.

For example, the company produces components for flush tanks, supplying parts for various global concerns, as well as independently creating finished products.

The Geberit system for toilets is very popular. High performance and reasonable cost make these devices very popular on the market.

More about fittings

Construction ( drain fittings Geberit), located in the toilet cistern, works when flushing occurs. The drainage mechanism consists of the following elements:

A tank is a container in which water is stored. Water hose can be supplied either from below or from the side. As a rule, the volume of the tank is about 8-10 liters.
The shut-off system is a mechanism responsible for filling the tank, as well as stopping the water supply when its level reaches a predetermined maximum.
Drain system - works when a button is pressed or the button lever is raised - depending on design features execution.

Lever models are now being produced less and less - they are being replaced by modern push-button models, which are more convenient, look better and allow the use of flush modes. When you press the button (lever), a hole opens through which water from the tank enters the toilet bowl. The hole closes when the container is empty.

Almost always the system is offered as a kit, already assembled and ready for use. If it fails, it can be replaced separately.

It should be borne in mind that if Geberit was installed, then it must be replaced with the same one.

The drainage system consists of two main elements: a lever and a siphon. The latter is needed to prevent water leakage: it covers the drain hole. As a rule, the appearance of a siphon resembles a plunger.

The button lever activates the siphon, which rises and opens the drain.

IN Lately appeared additional element, which is connected to the button (as mentioned above). Pressing it activates the button lever, which raises the siphon.

Moreover, many models are equipped with double buttons - which allow you to empty the tank completely (when pressed fully) or partially (respectively, when pressed partially).

Product classification

One way to classify the drain mechanism is the material of manufacture. The most common are plastic and bronze. Such product options cope perfectly with the tasks assigned to them.

The use of such materials is relevant because they are neutral to corrosion under the influence of moisture (unlike metal structures).

Geberite is a high quality plastic elements, and in terms of strength characteristics they are almost not inferior to bronze ones.

Can also be classified drain mechanism(tank) by design features:

push-button – modern solution: draining occurs by pressing a button (tank);
exhaust (lever) – outdated example when it is necessary to pull the lever rod up.

Installation (push-button options) is divided into types:

full drain - when you press the button, the entire volume of the tank is drained;
dual-mode use - the button is divided into two parts, which makes it possible to use only part of the volume of water in the tank: with the first press, water starts, and with the second, the supply to the tank stops.

In addition to the options considered, there is another modern solution - installation. This complex system For hidden installation plumbing equipment.

Thanks to the special design, a number of advantages are formed:

communications are aesthetically hidden;
space is saved in the bathroom - which is very important considering that there is often very, very little space in them;
plumbing fixtures - suspended;
easy installation and adjustment of Geberit fittings.

The installation distinguishes between two types of installations:

block - tank with fastening; implies fixation on the main wall, the elements are hidden in a niche, only displayed drain button and terminals for connecting communications;
frame - allows installation on main walls, as well as on the tank or its partitions. Eat corner models: with mounting on two walls.

The block system costs less, but the frame system opens up more possibilities for use.

Frame fittings (installation) for Geberit toilets are produced in three types:

universal;
for installation on lightweight walls, for example, plasterboard;
for fixing on load-bearing walls, for example, brick.

When it comes to Geberit installation systems, two main groups of devices can be distinguished:

for sinks, urinals – universal option for connecting plumbing equipment from different manufacturers;
for wall-hung toilets - a flushing tank and a button.

Nuances of choice

You need to choose drain fittings based on the toilet model. After all, the solution must be constructive; differing models cannot be reconciled.

So, if you plan to use a classic toilet, then the appropriate drainage fittings should be selected. In this case, you can count on the reliability of products, the design of which has been tested over many years of operation.

If a more modern solution is used - installation, it is worth taking into account the specific conditions in which the installation and configuration of Geberit fittings and the system as a whole will take place.

In this case, you can use a device that allows you to control it contactlessly, only by approaching or moving away from the sensors.

An important factor when choosing is price. The cost of conventional Geberit fittings is around $25. As for installations, in this case, of course, the price will be slightly higher - about $200.

In fact, this criterion is the limiting factor when choosing suitable fittings, as well as all plumbing equipment.

Otherwise, installations outperform classic solutions on aesthetics, ergonomics, functionality and durability.

Nuances of installation (video)

Setting up the mechanism

A ready-made toilet offered in a store always comes with the operating mode of the fittings installed and configured. However, in some cases you may need to configure it yourself.

This can happen during replacement - installing an entire new unit or its individual parts.

There is nothing particularly complicated about this - so it is not necessary to call a plumber to carry out such work (and for such work he will need to pay at least $5-10).

Now, actually, to how exactly this work is done. First, let's look at how to properly adjust the valve height:

The rod is disconnected from the overflow pipe.
The latch holding the “glass” is pressed out.
Stand - Moves up or down as needed.

Now let’s figure out the sequence in which the water level in the tank is adjusted:

The position of the “glass” changes - it needs to be either raised or lowered. In this case, there must be at least 45 mm of distance from the top of the part to the top edge of the container.
Overflow tube - installed above the maximum liquid level, minimum - 20 mm higher. However, it should be lower than top part racks - 70 mm minimum.

If you need to adjust a partial drain (in push-button models), you need to move its float higher or lower (relative to the overflow tube). There is an example in the video below.

For the same procedure, only performed for complete drainage, you need to move the valve itself (relative to the “glass”) - an example in the video below.

This adjustment will change (up or down) the amount of water that will be flushed when you press the button.

Advice! Similar products are produced serially, so there is no need to worry that you won’t find any parts during repairs, especially since the delivery set includes everything you need.

There are several modifications produced, and each has its own individual technical features, but the principle of their operation is the same. Their main difference is the type. It happens:

block;
framed

The first type has one significant drawback, since it can only be mounted on capital or load-bearing walls. Do it in, located in the central part Houses or , impossible.
The second type does not have this drawback, but has some reservations when securing it.

In addition, there are options that differ in appearance, which allow you to install toilet not against the wall, but in the corner.

It’s easy to find out which option is on sale: the block version does not have a sliding frame and consists exclusively of such components as:

fittings;
fasteners;
decorative fittings.

Choose a mount depending on the place where you plan to install the plumbing.

Preparation

Before starting the main process, you need to prepare working space and acquire the appropriate tools. The following will be useful to you:

perforator;
with drills (including for concrete);

building level;
roulette;
wrenches of the appropriate size;
knife and grinder with attachments for cutting drywall;
putty knife;
marker.

From additional Supplies will come in handy:

dowels installed in mounting holes;
silicone sealant;
polyurethane foam;
screws for gypsum boards;
finishing

If the procedure is carried out in a residential area, first of all you need to dismantle the old toilet seat and remove it.

The next step could be to move the sewer hole in accordance with the plan. This can be achieved using special devices - adapters made of plastic.

Note! This procedure will require dismantling the part.

To do this, the floor around the hole is deepened using a hammer drill and the adapter is fixed on it. Next, the free space around it is filled with cement-sand mortar or a self-leveling floor mixture. The next stage can be started after the solution has completely dried.

How to assemble a frame model for a wall-hung toilet?

The frame on which it is attached is assembled from the component materials. tank. You can adjust the height, horizontal and vertical position using the included brackets and screws attached to the frame.
The finished product will reach almost one and a half meters in height. In this case, its components will be at the following height from the floor level according to the standard:

If non-standard plumbing fixtures are used, these values can be adjusted in the same way as the distance between the toilet seat lugs. To extend service life, professionals recommend replacing metal racks with plastic ones if the appropriate size is available.

Note! Please note that a technological gap of 2 cm must be installed between the floor and the assembly.

Next comes the installation of the product. This must be done with strict adherence to horizontals and verticals. If necessary, a level, plumb line and marker are used for this purpose, which mark mounting points and lines. According to them, the finished frame is screwed to floor covering in advance drilled holes with dowels installed in them.

Important! When drilling holes in the floor, remember that there may be communications or a heating system running inside it. In case of damage, the front repair work may triple.

Do not forget that the height of the frame and compliance with the horizontal are varied with screws, and the quality of workmanship is checked building level.
Then you will need to connect the water supply using a flexible hose, and the corresponding complete fittings to the outlet from the sewer. If necessary, it can be replaced with a corrugated analogue, after which a final check for the tightness of the connections can be carried out.

Finally, plug the holes and install the mounting pins.

How to assemble a block model?

The peculiarity of this type is its versatility. In most cases, it can be used for floor and wall hung toilets, however the installation will vary slightly.

First, you will need to make markings, namely, mark the axis of symmetry and, in accordance with it, draw other points and lines. Their position and the required distance between them can be found in the complete instructions. According to the established marks, holes are drilled or punched with a hammer drill, and dowels are installed in them.
Next, you need to fix the drain tank and connect it to the water supply using a hose.
At the final stage, for a hanging toilet seat, you need to screw in the pins, and in the case of a floor-standing toilet, make new marks on the so that you can subsequently drill them and fix the fastenings, having previously done the same procedure with the knee. To connect them it is used special fittings called a cuff.

On a note! You may also need to cap the bolts and connect the button if this was not done by the manufacturer.

Geberit was founded in late XIX century. Nowadays, this brand evokes associations with very high quality, because over many years of work the company has gained an excellent reputation. Geberit installations are very popular among modern consumers: this equipment is reliable and durable. To avoid being disappointed with the results installation work, when installing the installation, you need to take into account certain rules that will be discussed in this article.

Peculiarities

A Geberit installation looks like a frame made of metal frames on which a sink, wall-hung toilet or other sanitary product is installed. All communications that are needed in a particular case are supplied to this equipment. A drain tank is also attached to the frame.

A significant part of the structure is hidden, and for this reason such equipment does not spoil the design of the room. The frame itself is usually attached to a main wall or partition made of plasterboard. She is in an upright position.

Advantages

Geberit installations have many advantages.

Long service life. The company guarantees uninterrupted operation equipment for ten years.
Maximum reliability. You don't have to worry about the structure ever falling down.
Saving space in the room.

Possibility of purchasing various components: gaskets, fasteners, exhaust valve to eliminate leaks, and so on.
The ability to use such a system to hide finishing defects.
Easy and quick to assemble.
No risk of leaks.
Aesthetic appearance of the structure.

One of the main advantages of such installations is the regulation of water drainage. Using a special button you can control the fluid flow.

Types of frames

There are the following types of such systems:

Frame. These structures are attached to load-bearing or main walls;
Block. Such systems are mounted on plasterboard walls and thin partitions;
Universal. These installations are suitable for various walls.

The manufacturer creates structures that can be placed in the most different places indoors - even under windows. Equipment with a height of up to 82 meters is intended for this purpose. This type includes Omega systems.

Designs from the Delta series can be classified as economy class, they have relatively low prices, but at the same time, in terms of quality, these structures are in no way inferior to other products from Geberit. The lower supports of such systems are reinforced and are suitable for installation on plasterboard sheathing.

The Plattenbau collection is designed specifically for buyers from the CIS countries. Such structures can be installed in walls with plumbing shafts. The manufacturer takes into account the thickness of the walls and partitions. The depth of Plattenbau structures does not exceed 12 cm.

Products from the Duofix collection are also popular. These systems are designed specifically for plasterboard partitions. Wall-hung toilets can be mounted on such structures. Such plumbing products are very convenient, because dust will not accumulate on the toilet leg.

The Duofix system can be installed in such a way that it is suitable for people with disabilities. The toilet is mounted in such a way that the load is distributed on the side racks and on the floor. For this reason, you don’t have to worry about the hanging product falling.

The structures from the Kombifix collection are very well suited for installation in front of or in brickwork. Such a system can be attached to the floor or to the wall.

Tools

Geberit structures can be installed independently, without the help of professionals.

To do this, you must first prepare all the tools necessary for the job:

hammer drill, drills;
marker (to make markings);
building level;
spanners;
plumb line, tape measure.

Frame design

First you need to choose the place where the structure will be installed. When choosing a suitable installation, you should take into account the thickness of the partition or wall. It will also be necessary to pay attention to the features of the sewerage system.

Installation work must be carried out in a certain order.

Assemble the frame. It will be necessary to make a metal frame where the movable fasteners are located. The drain tank will be fixed on them. Since the fasteners are floating, you can set a suitable height at which the plumbing product will be fixed. The frame can withstand a very significant weight (up to 500 kg).
Then you need to install the tank. You should leave a small distance between the wall and the tank (about 15 mm). Place the drain button at a distance of 100 cm from the floor.

Attach the assembled structure to the wall. To do this you need to use a building level. First, hold the frame up to the wall and mark where you will make the mounting holes.
Connect the pipeline to the tank. The direction can be side or top. It is better not to choose flexible hoses for connecting the tank, otherwise it is quite possible that these elements will fail at the most short time. It is recommended to opt for plastic pipes.
Then the system must be connected to the sewer. Corrugation is used for this.

Check how the installation works. Inspect all connecting elements: there should be no leaks. If everything is in order, you can close the frame.
Install the plasterboard box. The frame for the box must be metal profile. It is recommended to opt for plasterboard, which is highly resistant to moisture (especially in cases where there is both a bathtub and a toilet in the same room). It is better to choose sheets with a thickness of 10 mm. You can install drywall in two layers. You should first cut out all the necessary holes in the sheets.
Install the toilet. Installation can be carried out approximately ten days after installation of the box. The plumbing product should be installed on pins. You can line the box before or after installing the toilet.

Installation of a block structure

The installation of the block system will take a minimum amount of time.

This work will need to be carried out as follows.

Mark where exactly you will install the structure. It should be taken into account that the axis of the structure must coincide with the axis of the room.

Mark where the tank will be located. Usually the height does not exceed 100 cm. Screw in the dowels at the same distance from the axis. The holes should be made using a hammer drill: then you need to hammer the dowels into them.
Install the tank.
Mount the pins: the toilet will be attached to them. Attach a bowl to the drain. Clamps must be used to attach the hose.

Possible problems

Geberit products should be purchased from a branded or certified store. It is not recommended to choose too cheap designs or contact unreliable sellers, otherwise it is quite possible that you will receive a low-quality product.

Owners of Geberit systems sometimes face different situations.

The plumbing product begins to wobble. This problem is very easy to deal with: you just need to adjust the fasteners, tighten them;
The liquid stagnates in the sewer drain. This means that the slope of the pipes is not correct. Usually it is 45 degrees;
The drain tank is leaking. In such a situation, you will need to check whether the gaskets are installed correctly;
The toilet is leaking. It is possible that there is not enough sealant at the joints. To fix this problem, clean the seams and reuse the silicone.

The manufacturer Geberit produces high-quality and reliable installations complete with toilets, making the bathroom more comfortable and convenient. Wherein appearance premises, as evidenced by user reviews, is very beneficial. The fittings can be easily installed by following the installation instructions exactly.

Types and advantages of Geberit installation with toilet included

Installation systems with toilets are produced by many manufacturers. Their range is varied, but the best is Geberit. The company produces installations of 2 types: block and frame. The first is simple, but it is fixed only in niches of main walls. The frame installation includes a steel frame and components: sewer outlets, fasteners. This design can also be angular.

The steel frame will allow you to secure the structure without placing a large load on the wall

The big advantage is that its installation is possible where it is not technically possible to install other structures. A special frame and half-meter studs allow installation even if there are pipes behind the toilet.

In addition, users like:

Easy to install.
Swiss quality and precision.
Long warranty (10 years).
Guaranteed availability of spare parts. When the model hidden system discontinued from production, spare parts for it are stored for 25 years.

Attention! If there are no main walls in the bathroom, then it is possible to install only a frame installation.

Installation instructions

Geberit fittings are attached to the base of the toilet using a drain pipe connected to it at an angle of 90 degrees. This is proven reliable design. The set includes a flap that covers the joint and a decorative cuff for the pipe. Although the internal mechanism is located in the wall. Access to drainage structure possible via the flush plate.

Despite its external elegance, the design can withstand heavy weight

Installing a block installation

To install you will need the following tool:

perforator;
keys of the required sizes;
marker.

Installation process consists of several steps:

Installation of frame installation

The technology for installing a toilet with a frame installation is as follows:

Tip: When connecting the drain tank, do not use a flexible hose. It is short-lived, and to replace it you will have to destroy the wall.

Reviews

There are usually no complaints about the quality of the Geberit installation complete with a toilet:

Olga. An experienced specialist was invited to install the installation. Particularly delightful is the operation of the automatic drain. It feels like this technique is for humans.
Igor. The Geberit installation is smart and reliable. Every little detail has been thought out.
Andrey. It is not for nothing that Geberit is in the highest price category. I like everything, especially the design of the flush panel. The frame is powerful, the fittings are reliable.

Installations fit well into the interior of bathrooms

Artem. I installed the Gebirit DuoFresh model. Very good, has an odor removal function - complete exhaust fan with a filter, you can put in tablets.
Marina. Impressions from the Gebirit installation are only positive. Water is drawn silently, the buttons do not stick. During the year of work there were no complaints.
Vadim. I recommend Gebirit to my customers. The installation is reliable, even after a long time it does not change geometry and does not fail. If you need to replace something inside, you do not need to disassemble the wall - the installation elements can be removed through the hole for the button.

Installation with wall hung toilet Gebirit looks elegant. It fits harmoniously into the design of the bathroom.

Geberit - installation: video

Geberit installations: photos

The Swiss company Geberit produces and supplies Russian market several installation models. Compact designs are popular among consumers due to their reliability, aesthetics and ease of installation.

Features of the Geberit installation

Installation Geberit

The Geberit installation is available in two types of designs and three product lines. Block type is designed for installation in a niche of main walls. The frame consists of a rectangular steel frame and components. Can be attached anywhere.

The Geberit WC system is available in three versions: Sigma, Omega and Delta.

Sigma is a premium line. The consumer is offered wide range design solutions keys: from durable plastic to gold plated. Delta is a budget offer with a limited set of buttons; there are no significant differences in functionality. Geberit Omega is designed for installation under a window in private houses with a pitched roof.

Delta and Sigma series are available in different options: ultra-thin 8 cm, standard 12 cm, for people with disabilities. The Plattenbau modification is intended for panel houses.

All Geberit products have the following advantages:

saves space in the bathroom;
allows installation in any convenient place;
Possibility of selection for any apartment and private house.

The installation can be purchased complete with a toilet.

Popular models

Model “Geberit Duofix UP100 458.103.00.1”

The domestic market offers a wide range of Geberit products, popular models:

Geberit Duofix UP100 458.103.00.1 is attached to the wall and floor, has top bar on a frame on which you can build a shelf. The flush key must be purchased separately. There is a variation without the top bar.
Plattenbau 458.125.21.1 – set for panel houses. Features of the model are that the frame is fixed to the wall. The fasteners include 50 cm long studs and a special top strip, which allows installation to go around the pipes of the plumbing shaft.
Geberit Duofix UP320 111.300.00.5 belongs to the Sigma line. It has the ability to connect a wide range of flush keys in any design. Provides three types of control to choose from: pneumatic, mechanical or touch. Installation is carried out in a profile; the package does not include wall fasteners.
Geberit Duofix UP320 Plattnebau 111.362.00.5 belongs to the Sigma premium line. Combines hidden installation capabilities with a variety of design solutions.

The presented models differ in the type of frame structure and whether they belong to the budget or premium segment, depending on the variations in control and key connection.

The standard equipment for a Geberit toilet installation includes connecting pipes, frame mounting, shut-off valve, plugs, threaded rods, and fasteners.

How to choose a suitable design

Choice suitable model carried out according to the following criteria:

Type of building envelope. For panel ones, only Plattnebau is suitable.
Mounting option - in the floor, load-bearing or non-permanent wall, under a window.
Dimensions of the toilet. Mostly models are presented with a width of 50 cm, a height of 112 cm, and a depth of 8-12 cm. For people with disabilities, the frame has a double width.
Price. Choose from a budget or premium package.
Full or limited set of functions.

The Geberit installation can be supplied complete with a toilet, include basic keys, and a certain type of control.

Installation and connection methods

Installation of the structure

Installation methods depend on the type of structure. To install a block and frame installation, you need a marker, a set of plumbing wrenches, and a hammer drill.

The block option installation process consists of the following steps:

Determine the installation location. For a standard bathroom, this is a niche with a riser or the wall behind which it is located. The riser or branch to it must first be replaced with a metal-plastic one.
Make markings according to the dimensions of the frame.
Mark the height for attaching the dowels. The exact dimensions are indicated in the instructions.
Use a hammer drill to make holes in the wall and secure the dowels.
Mount the drain tank, connect the hose and tighten the necessary fasteners.
Connect the water.
Check how water is collected and flushed into the toilet.

The frame installation is mounted as follows:

Assemble the frame. The finished frame will have a height of 1.3 to 1.4 m.
Secure the tank. Place the flush button at a height of 1 m from the floor, a wall-mounted toilet at a height of up to 0.45 m, and a sewer outlet at a height of 0.25 m.
When installing, use a level, otherwise the drainage system will be disrupted. Align vertically and mark holes for fastening the frame.
Use a hammer drill to make holes for fastening. Mount the frame on dowels to the floor and to the wall.
Connect the water supply to the drain tank.
Connect the riser to the toilet outlet.
Tighten the fasteners and check for leaks.
Cut drywall to size to cover the frame.
Fix the drywall and make finishing tiles or other material.
Hang the toilet.

exploit installed structure maybe in a week.

Main types of breakdowns and how to avoid them

The following problems may occur:

Drain tank leaking. In this case, you need to check the correct installation of the sealing gaskets.
Leaking toilet. The joints are most likely poorly sealed. It is necessary to clean the seams and reuse the silicone.
Toilet shaking. To solve the problem, you need to tighten the fasteners.
Stagnation of water in the sewer drain. The slope of the pipes does not correspond to the recommended 45 degrees. You will have to dismantle and adjust the angle of inclination.

It is better to entrust the installation and correction of problems to a specialist to avoid mistakes.