The threshold under the front door prevents cold air and dust from entering the house from the street. This simple design tightly closes the gap to the street underneath door leaf, therefore it becomes a good sound and heat insulator. In addition, it prevents the door from being broken into.
The threshold is a bar that is located at the bottom door frame.
This design for a private house is made with your own hands from the following materials:
If the strip comes with the door frame, then you don’t have to select a design - it is simply installed when installing the frame. If the front door kit does not provide it, then you need to independently select the material and its design. Installation is carried out after installing the box.
When choosing a design type, consider the following parameters:
To ensure that the threshold fits the door as tightly as possible, select the correct shape and size of the product. It is better to order it together with the door frame.
Different shapes seal for entrance door The height of the product determines how tightly the canvas will adhere to the threshold. However, it should not be made too high, since it is inconvenient to step over such a part when entering or leaving the house. Insufficient threshold height will not be able to provide reliable protection your house. Recommended height - 30 mm. Some seals are equipped with additional locking structures.
Threshold under the entrance door with holes for crossbars of a locking design When choosing a material, remember that the threshold is subject to mechanical stress during operation, and therefore it must be durable. Wood, concrete or metal are suitable for the entrance threshold.
If you decide to make a wooden threshold, install a plank made of hardwood, such as oak. Such a product will require constant care to maintain its aesthetic appearance and increase its service life, such as painting or varnishing. Wooden construction is the least durable compared to concrete or metal, but it is easier to repair and, if necessary, dismantle.
Attention! To increase heat and sound insulation, install a structure with a rubberized insert.
To ensure quality installation work, first prepare tools and materials. You will need:
At this stage, the installation site of the strip is cleaned. If there is an old threshold already installed, then it is dismantled. They level the base, remove beads of concrete, plaster the holes, clean out dirty places, and sweep away debris with a broom.
At this step, measure the distance between the vertical posts of the box and determine the desired width of the structure. Next, a wooden board with the following parameters is purchased.
It is advisable to make the threshold wider than the door frame. Then, if you cut out the corners vertical racks to the height of the threshold, you can install it in the box. At the same time, it is better secured and strengthens the box itself.
The plank is installed in place using a building level. It is imperative to check how the door works when set bar. It should open and close freely. When closed, the bottom of the door should fit snugly against the ridge on the threshold. After checking, the threshold is secured with screws or nails.
Finish the threshold using staining oil paint or varnishing.
Wooden threshold So that when fixing the threshold wooden plank not cracked, holes are first drilled in the places where nails should be driven in.
Building such a structure is labor-intensive, but the product will last much longer than a wooden one.
Same as installation wooden structure, first dismantle the old threshold and clean the base for the new one. Seal cracks and holes with cement-sand mortar.
Formwork is made from wooden boards or slats around the perimeter of the threshold. It must be securely fixed. Installation is carried out by level.
Attention! To create a durable structure, screw into the base of the threshold metal bolts to the height of the structure (they play the role of reinforcement) or lay metal mesh, wire
To mix the concrete solution, take cement and sand in a ratio of 1:3. It is advisable to add plasticizers to the mortar mixture, which will make the structure frost-resistant. You can use ready-made mixtures that are sold on the construction market.
Pour the solution into the formwork and carefully level it so that all corners are filled with concrete. Now all that remains is to wait for the solution to dry. During drying, the surface of the threshold is moistened from above with water several times so that drying occurs evenly and the concrete does not crack.
It is also called automatic lifting threshold. This design is installed at the bottom of the door. The insertion is carried out to a depth of 20 cm.
The threshold is made of aluminum with a seal made of rubber or rubberized material and a spring.
Guillotine type threshold On the side of the hinge post, a strip with a button is cut into the door. When closing, the button is pressed, the threshold spring is activated, and the seal falls down to the floor covering.
The service life of the structure is up to 25 years.
Such a system is easily repaired, and damaged parts can be replaced.
The gaps between the base floor and the threshold are filled concrete mortar. After drying, it is puttied with silicone putty. The metal threshold that comes with the box does not need any decoration.
Metal threshold In a wooden structure, cracks and chips are repaired with wood putty, the plank is primed and then, at the owner’s discretion, painted or varnished. The junction between the structure and the floor is decorated using a plinth.
For concrete structure Painting, tiles or linoleum are used as finishing. The joint can also be hidden using a wooden, plastic or metal baseboard.
Ceramic floor tiles for finishing the door threshold are matched to the color of the main floor near the entrance door.
Threshold from ceramic tiles To finish tiling you will need the following tools and materials.
Before finishing, the base under the tiles is cleaned and leveled.
The adhesive is applied using a notched trowel to the tile and base. Next, the tile is pressed against the threshold with your hands. To ensure a tight fit, tap it with a rubber hammer. The correct installation is checked using a level. The tiles are laid nearby at a distance of 2-10 mm. Plastic crosses are inserted between the elements. Once the tiles are laid, you can begin to design the riser. The seams on the threshold and on the riser must match.
After the glue has dried, the crosses are removed and the seams are made using grout.
In contact with
Comments
Unfortunately, there are no comments or reviews yet, but you can leave your...
New articles
New comments
S.A.Grade
SvetlanaGrade
SergeyGrade
SergeyGrade
AlexeiThe threshold at the front door of an apartment is considered an important detail, since it:
This design allows you to protect your house or apartment from thieves. In addition, thresholds help to even out differences between the doors and the floor.
Some property owners are interested in how to make a threshold correctly with my own hands. Experts recommend doing this structural element no more than 3 centimeters high. Sometimes this parameter is reduced to give the interior a beautiful appearance, and in other cases it is increased taking into account the thickness of the carpet in the hallway.
The door, thanks to the threshold, fits tightly to the doorway, seals it and thereby helps prevent strangers from entering the house.
You need to know how to make the entrance door threshold in an apartment so that it decorates it and at the same time does not catch the eye, therefore, to equip it, you should select the appropriate material. The duration of operation depends on how correctly this is done.
You cannot create a structure that is too high, as it will cause inconvenience for people visiting the house. Incorrect choice This parameter may cause insufficient protection of the home due to the appearance of a gap between the door and the threshold. This defect will help thieves break into the apartment. Also, the presence of a gap will make the thermal insulation of the house insufficiently reliable.
There are certain requirements for how to make a threshold at the front door. It must match the door in color and material.
For this reason, the threshold installed at the entrance to the home is made of:
When the material from which it is planned to make the threshold has been determined, they begin to choose its shape. According to experts, the most functional design is in the form of a staircase, as in the photo.
Today in practice they use different variants making a threshold at the door. Optimal choice depends on the material used. Before making a threshold in an apartment, you need to remember that this element must not only correspond to its functional purpose, but also to decorate the interior. The structure should be arranged so that the steps are integral with the beginning of the floor covering.
During the installation of the front door, irregularities always form and before eliminating them, it is necessary to carry out a number of preparatory measures:
The arrangement of the entrance door threshold involves covering its surface with a sealant so that it cannot be affected by natural influences. We should not forget that this design is intended to retain dirt and dust, which residents and their guests sometimes bring into the house on their shoes. Therefore, when cracks appear in the threshold, they must be eliminated using sealants.
Before pouring the entrance door threshold using cement mortar, prepare the following materials and tools:
The components for the solution are mixed in the proportions specified in the instructions on their packaging. The mixture should not contain too much water - otherwise the quality of the structure will deteriorate as bumps will appear on it. To give the solution elasticity, special additives are added to it.
The composition should be stirred using special attachments on a puncher until a consistency similar to thick dough is obtained, avoiding the formation of lumps in it. The prepared solution must be used within two hours; after this time, the mixture will lose its quality characteristics.
During the pouring process, bubbles may form - they are pierced with a knitting needle. During the first 10 days, the flooded threshold should be moistened with water. Finishing the threshold of the front door to give it beautiful view and increasing the degree of wear resistance is made from paving slabs. It is laid on the outside with special glue. All formed seams are sealed with putty.
Typically, a wooden threshold for an entrance door is made from birch or oak boards, pre-treated with moisture-proof compounds that prevent them from swelling.
First, tools and building materials are prepared, including:
The work is performed in a certain sequence. First, remove dust and dirt using a vacuum cleaner.
Then the horizontal level is checked with a level. Fix the threshold to the floor with nails or screws. The structure is varnished. The wooden threshold is designed depending on the preferences of the home owner.
Nowadays, metal door thresholds are often installed at the entrance to an apartment. These products are made of aluminum, brass or of stainless steel sold in a wide range.
Want to build a porch yourself? No problem! Be it concrete, be it wood, or be it metal – choose any one. In this case, the metal will be made with a beautiful canopy roof made of
Reliable, durable and overall solid design.
Dimensions of steps: a - normal; b - outsiders Typically a porch consists of several steps. Our task is to choose the best design dimensions.
The optimal width of the stairs is 80-100 cm. If possible, the width should be increased - this will make the porch more comfortable and beautiful. It is not advisable to reduce it.
The permissible angle of inclination of the stairs is from 27 to 45 degrees.
| Step width, mm | Step height, mm | March inclination angle, degrees. |
|---|---|---|
| 400 | 100 | 14 |
| 380 | 110 | 16 |
| 360 | 120 | 18 |
| 340 | 130 | 21 |
| 320 | 140 | 23 |
| 300 | 150 | 25 |
| 280 | 160 | 29 |
| 260 | 170 | 33 |
| 240 | 180 | 37 |
| 220 | 190 | 40 |
| 200 | 200 | 45 |
We make the steps approximately 25 cm in width and 12-20 cm in height, depending on who will use the porch. Children and elderly people? Making the steps lower. Mostly young and energetic users? We can increase the height of the steps.
We arrange the upper platform so that it is approximately 50 mm below the end of the front door.
We dig a pit around the perimeter of the future porch. Depth – from 50 cm.
We install formwork around the perimeter of the foundation.
We fill the bottom of the pit with a 20-centimeter layer of crushed stone and compact it. Pour a 10 cm layer of sand on top. Spray with water for better compaction.
We cover the area with roofing felt. We lay the reinforcing mesh (recommended cell size is 10x10 cm) and. You can prepare the solution yourself. Standard proportions:
We pour concrete. We level the filling and pierce it with reinforcement in several places to release excess air. We leave the concrete for several days to gain initial strength.
Cement and base mixtures
We build formwork for the steps. For this we use thick plywood. The height of the formwork should be 20 cm higher than the height of the future porch.
The principle is simple: we cut out the formwork elements according to the height of each step and install them in the appropriate places. We tighten the shields together with metal plates, wooden blocks or other suitable fasteners.
Important! The side panels need to be strengthened with additional stiffeners.
The steps must be reinforced. In this case, the reinforcement must be laid and installed in all three planes. Even more convenient option– weld the frame in the shape of the future staircase and build formwork around it. Do as you please.
Lubricate the inner walls of the formwork with oil. Thanks to this, in the future we will be able to remove it without much effort.
We prepare the mortar for pouring in the same way as the mixture for the foundation-platform.
We fill the stairs in stages, starting from the first step. Let each step dry slightly, and only then fill the next one. In this case you need to install additional elements formwork with front side steps. The length of these elements must correspond to the width of the stairs. We make the height the same as that of the step itself.
Important! The side of the formwork in contact with should be as smooth as possible.
We carefully level the poured concrete and pierce it with reinforcement in several places.
We remove the formwork after at least 7-10 days. In conclusion, all we have to do is execute finishing steps. We can cover them with stone or tiles, lay them and perform any other finishing at our discretion.
We install railings upon request. The height of the handrails is from 90 cm. You can use the following option. It is also suitable for metal and wooden porch(in this case we will replace metal elements wooden).
We install support posts made of metal pipes in the lower and upper parts of the porch. It is advisable to select the length so that the slope of the railing matches the slope of the stairs. We connect the upper and lower ends of the racks with pipes of a slightly smaller cross-section. We use welding.
The top tube will take on the functions of a handrail. To fill the space between our pipes we use any rolled steel. We install elements at any interval. At this point, everything completely depends on your preferences and imagination.
After installing the structure, we clean the metal elements and prime them in 2 layers. This treatment will increase the service life of the railings.
This porch will go well with almost any home.
In general, the foundation is arranged in the same way as in the case of concrete porch, with only one difference: at the same stage you need to install supports for the future canopy.
It is better to install supports in each corner of the future canopy - this way the structure will be as stable as possible. If the porch is large, we make supports along the length of its walls in increments of no more than 2 m.
We dig holes about one and a half meters deep for each support. They will cope with the role of supports perfectly metal pipes. We insert the pipe into the hole and fill it with concrete.
The supports can also be made from bursa. The operating procedure is the same, but first the lower part of the beam must be wrapped in roofing material or tarred and additionally soaked with an antiseptic.
At the same stage, we install supports for the future staircase. Similarly, we dig holes, place metal posts in them and pour concrete. It is unlikely that the porch will have too long a staircase, so it will be enough to install supports at the bottom and top of the structure. For greater confidence, we can install them in the middle of the span.
The further procedure, up to the stage of pouring concrete, remains the same as in the instructions for arranging a site for a concrete porch.
At the pouring stage, we take into account that we will need to drown the staircase structure somewhat in the solution. We do not fill it to the very top of the site - we leave approximately a 100-300 mm gap (depending on the dimensions of the structure being equipped and its features).
Then, after installation metal structure, we will fill the pit to the very top.
Drawing according to the house plan 
Let's take two metal channels. We weld them to the previously installed and concreted supports. In the future, we will weld rolled products for steps to these products.
We take equal flange metal corner. We cut it to the selected length of the steps, increased by the length of the welding seam. We weld the metal corner along the contour.
We get products in the form of the letter G. We connect them together. At the top we connect these L-elements using an equal angle corner. To do this, we weld it along the contour to both products, placing the shelves inside. To connect the bottom of the steps we use a similar corner, but we place it with the shelves facing outwards.
To fill the steps we can use different materials, for example, wood and plywood. Fastening is carried out using self-tapping screws, screwing them in from the bottom. For additional fastening of wooden elements we use silicone and regular glue.
In general, decorate the stairs at your own discretion. If you wish, you can not seal the horizontal openings, but simply mount the sheathing directly on the steps.
Welders
We installed the racks for the frame at the stage of arranging the foundation. Next we work in this order.
We install transverse supports according to the dimensions of the frame. If desired, we can make a curved canopy. To do this, just cut the profile in increments of about 4 cm and bend it to the desired level. The advantage of a curved canopy is that precipitation and various debris will not linger on it.
We lay it on the frame and secure it with self-tapping screws. We maintain a fastening pitch of 300 mm. We glue the edges. At this point the canopy is ready.
– The best decision for a wooden house porch. Such a foundation is simple and quick to install, but at the same time very reliable.
We dig holes at the points where the pile is installed - in the corners of the future porch and along the length of its edges in increments of 80-100 cm. The depth of such holes is from 80 cm. Optimally, below the freezing point of the soil.
We treat the support beam with an antiseptic, wrap its lower part with roofing felt, and then insert it into the holes. Fill the vertically aligned timber in the pits with concrete.
Let the concrete harden and proceed to further activities.
If necessary, we cut off the tops of the timber so that all the piles are at the same level. We calculate the height of the supports so that after laying the platform between it and the front door there remains approximately a 5-centimeter difference in height.
We attach the logs to the supports and the wall of the house in a suitable way (with self-tapping screws, dowels, etc., depending on the wall material).
We begin to manufacture the load-bearing part of the stairs. We will attach steps to it. That is, the bowstring is side edge steps.
To make a bowstring, we use wooden boards with a thickness of 5 cm. We take the board and draw steps on it. We cut out the blanks with a jigsaw or saw.
We fasten the string with the lags using a tongue-and-groove connection.
We screw or nail the platform sheathing boards to the joists. If desired, lay some kind of material on top of the boards. finishing coat– we focus on our preferences.
We attach risers and treads to the string. We start working from the bottom step. The procedure is simple: fix the riser, attach the tread to it, and so on until the end. For fixation we use self-tapping screws or a tongue-and-groove connection.
Arrange the railings and canopy at your own discretion. Installation instructions for these elements have been provided previously. The sequence remains the same, you just need to replace the supporting elements and cladding parts with similar products made of wood or other preferred material.
Construction boards
Happy work!
Very important detail The threshold for the front door is considered. This element of the house is very often simply forgotten and such a design is considered not very important. This opinion is deeply erroneous. It performs quite a few functions:
The door threshold protects the room from dust, noise and cold air.
This detail of houses helps out when it is observed strong drop floor level. In this case, it begins to perform a kind of decorative function, hiding such a defect. The question arises, how to install an entrance door without using the services of professionals?
Thanks to the threshold, the entrance door fits tightly and seals the doorway, helping to prevent possible break-in. In addition, with its help it is held in door block metal entrance door.
The threshold should enhance the appearance of the house. Therefore, to make a threshold, you need to select suitable material. Its service life depends on this. When a master begins to make it, he must take into account the element of safety. It cannot be made too tall. The high altitude will be a source of inconvenience for visitors to the house. Basically, the height of the threshold should not be very large, but also not very small. Her wrong selection will cause a lack of protection for the home due to the formation of a gap between the door and the threshold. It will help thieves get into the house. In addition, the gap will become a source of disruption to the existing thermal insulation. To add elegance, you can make it in the form of a continuation of the steps of the entrance staircase.
For manufacturing it is necessary to select a material. Most often used:
After selection required material begin to create its form. The threshold that looks like a staircase is considered the most functional. Today we know a lot of the most different ways production of the entrance door threshold. The optimal option depends on the material used. You must always remember that this element of houses, in addition to its functional features, performs the task of decorating the design. The threshold must be made in such a way that the steps become one with the beginning of the floor.
Before you begin to fill in the unevenness that is formed during the installation of the front door, you need to carry out preparatory work. Use a vacuum cleaner to remove dust and accumulated debris. The cleaned surface must be carefully examined to detect peeling and various cracks. Existing defects must be cleaned, very large cracks must be covered with cement mortar. All loose pieces must be removed.
The surface of the made threshold must be covered with sealant.
This is necessary because it is very strongly influenced natural conditions. It should be taken into account that its function includes the retention of dirt, which can be brought into the house by visiting guests and the owners themselves. Therefore, it is advisable to seal the resulting cracks with sealants.
To form a concrete threshold, you must have special tools:
To obtain a more reliable adhesion of concrete to the screed, the surface must be treated with a primer. For a small step you need to do wooden formwork in accordance with its dimensions. The filling composition is made in strict compliance with the instructions.
There should not be a lot of water in the solution, otherwise the strength of the screed will deteriorate and bumps will form on it. To make the composition more elastic, special additives are added to it. It must be stirred until a thick dough is obtained, and the formation of lumps is unacceptable. For this type of work, special attachments for the hammer drill are used.
The prepared solution must be used within two hours, otherwise in the future it will lose all its positive traits. Bubbles that will form during pouring are pierced with a knitting needle. Over the next 10 days, the screed must be moistened with water. This is done so that the concrete becomes stronger as it dries. To give the threshold a beautiful appearance and increased wear resistance, it is laid out outside paving slabs. The upper surface of the threshold is covered with tiles laid on a special glue. All seams are sealed with putty.
Birch or oak boards are most often used to make a wooden threshold. They are pre-coated with moisture-proof compounds. The fact is that during operation it can begin to swell greatly, and the front door will no longer close tightly.
To make a wooden threshold, you will need to have the following types tools and materials:
When forming a threshold from wood, a certain sequence must be followed:
The final finishing is carried out depending on the individual taste of the owner. It can be painted to match the color of the door. To create an impressive design, you can trim the threshold with linoleum or cover it with tiles. Sometimes a plinth is installed.
In conclusion it must be said that door threshold is functional design. Therefore, it needs to be made durable and beautiful. Before installing it, you need to take care of it appearance, convenience and practical properties.
The process of installing doors is significant, and finishing the threshold and correct installation are also important. Not everyone understands how important the threshold is in the interior. However, the functionality and benefits are clear.
Various door threshold options
| Threshold functionality | |
| No. P/P | Characteristic |
| 1 | Soundproofing function. The role is fulfilled productively if the threshold is combined with a rubberized jumper. |
| 2 | Additional thermal insulation. The interior element does not allow drafts and cold from other rooms to pass through. |
| 3 | The aesthetic function of the threshold also does not go unnoticed. With the help of this part of the interior, the doorway looks neater and more attractive. |
| 4 | Installing thresholds allows you to comfortably distribute space during repairs. This is convenient because you can separate flooring in one room, from covering in another room. |
These are just some of the benefits that the completed finishing of the threshold of an entrance door, interior door or door to another room provides.
If you plan to make such a threshold beautiful when it is already ready, then you need to study the installation features. These are:
To get a high-quality design element for a room, you need to perform all the steps one by one. The sequence of work is as follows:
Regardless of what options for thresholds for the balcony you decide to make, you will definitely need materials and tools. The following set of raw materials is most often used for installation:
If the owner decides to make some kind of reality special option threshold design, then additional tools or materials may be required that are not included in the list above.
You should be especially careful when finishing the threshold.
Door sill finishing options
After all, the success of the renovation transformation depends on the quality of this process. It is important to study the design options for the threshold to choose the right one for your apartment or house. Please pay attention to the following areas:
Each room has its own characteristics of finishing the threshold surface. Therefore, you should pay attention to the recommendations and design rules.
Watch the video: review of the ideal threshold to the bathroom.
Finishing the threshold to the balcony is a responsible and important mission. In addition to visual transformation, such a threshold will help retain heat in the room and ensure comfortable movement around the space.
The threshold of the balcony also protects the floor covering of the room, protecting it from moisture and fungal growths that can enter the room from the street.
There are several options for finishing the threshold of a balcony door; each owner of a house or apartment will be able to choose the best one according to his preferences and financial capabilities. The following ideas should be taken into account:
Any of the options is excellent for carrying out the mission of threshold equipment under balcony door. The main thing is to carefully study the nuances and features of working with each material.
If the building is brick, then such a threshold will ideally suit the overall picture of the house cladding. In order for the design to be carried out on top level, you should prepare for the process. The sequence of finishing the balcony threshold with brick is as follows:
Many people prefer plastic coverings. This material perfectly repels moisture from the inside of the threshold and protects the surface from corrosion. The work should be carried out in this order:
This option has many advantages, such as:
But there is also a drawback that is quite significant. Plastic is a short-lived material. Therefore, the duration of its operation is no more than 2 years. Due to the fact that the threshold is a structure that regularly bears loads, cracks and deflections may appear on the surface over time.
Design options for plastic thresholds on the balcony
But if a temporary option suits the owners of a house or apartment, then a plastic threshold may well be the choice.
The entrance door threshold can be arranged in several options. If we're talking about about the front door of a private house, then you should pay attention to the same finishing ideas as in balcony threshold. The only thing is that you should exclude the option of a plastic threshold, because it is unlikely to look aesthetically pleasing against the background of the facade of the house. Although, if the sheathing is made of siding, then a plastic threshold is quite suitable.
Entrance door threshold device
When it comes to the threshold of the front door in a high-rise residential building, most often they choose one of the following options:
As a rule, the size of the threshold is adjusted depending on the height of the difference that is measured building level. The metal threshold can be:
You need to act one by one and harmoniously, the sequence of work is as follows:
After completing the above processes, the issue of setting the threshold for the front door can be considered completed.
If you plan to install wooden door, then you can pay attention to such a finishing option as laying tiles. The procedure is as follows:
With this finishing option, the front door opening will look aesthetically pleasing and neat.
When equipping a wooden threshold, the same materials and tools are used as when finishing the threshold of a loggia. The installation technology is also no different.
Need to take into account important nuance. If you plan to install a heavy, bulky door, then the wooden threshold may become deformed under it.
In this case, it is better to give preference to a metal or tiled threshold; they are stronger and more durable.
Wooden thresholds in section for interior openings
When installing a structure under the front door, you should take into account the functions of the thresholds. This elevation should provide protection from drafts, cold and dust. Therefore, when designing the entrance door threshold, these factors should be taken into account.
When it comes to finishing the threshold under interior doors, owners can take into account any decorating ideas. After all, the space under the interior doors of the kitchen, hallway, bedroom or nursery is least susceptible to external influences. Therefore, finishing can be done different materials both with laminate and with the installation of plastic thresholds. Naturally, before making an interior threshold, you need to first decide what exactly it will be.
An example of finishing a threshold with linoleum
Wooden, plastic, using tiles, the threshold is made using identical technology, as in the case of finishing a balcony or entrance door threshold. In the matter of finishing the interior threshold, it appears additional opportunity– laminate and drywall.
The process of creating a laminate threshold is similar in technology to installing a wooden threshold. It all depends on what kind of laminate is selected for the mission. If you choose a laminate that is assembled using a lock pattern, you should carefully adjust the height so that the structure is neat and uniform. 
For strength, a concrete niche is poured under the laminate required height, and after that a laminate is installed on top of the frozen hill.
Everything is simple, the main thing is to get into the grooves of the laminate locks and create a structure of the desired shape.
First you need to form and assemble a frame for drywall. This is made from profiles made of metal. The transverse and rack profiles need to be fastened together using screws or self-tapping screws. A shape should be formed that clearly fits into the brick threshold. Making a frame with your own hands is quite simple. The main thing is to act harmoniously and one by one. When the profile is assembled, it must be fixed to a previously prepared leveled surface.
The process of finishing the threshold with plasterboard
Afterwards the frame is sheathed with sheets of plasterboard. The pitch between the screws should be no more than three cm. This is how you can get a uniform and smooth texture.
On the street, a plasterboard threshold will not be very appropriate. But it’s suitable for equipping an interior threshold.
According to the technology of the installation process, finishing the threshold in a bathroom or toilet does not differ from all the previous options mentioned above. The main thing is to cover the structure with a moisture-repellent material after installation, which will protect the surface from premature wear and damage.
Option for installing a threshold in the bathroom and toilet
It is important not to use the threshold as steps. However, this structure is more fragile and bears the weight of the door frame and the door itself. At correct installation the threshold will last for many years and will provide an aesthetic appearance to the entrance structures.
