How to sew an ottoman with your own hands. DIY ottoman: step-by-step instructions on how to make original and comfortable furniture. What to stuff with to make it soft

Stairs. Entrance group. Materials. Doors. Castles Design » Stairs How to sew an ottoman with your own hands. DIY ottoman: step-by-step instructions on how to make original and comfortable furniture. What to stuff with to make it soft

How to sew an ottoman with your own hands. DIY ottoman: step-by-step instructions on how to make original and comfortable furniture. What to stuff with to make it soft

In order for a new comfortable and original piece of furniture to appear in your home, it is not at all necessary to go to the store and spend a lot of money. Of course, it’s better to buy a sofa or bed, but such an interior detail as an ottoman is not at all difficult to make with your own hands.

In addition, if you decide to start making an ottoman, you can make it the one that best suits your design.

You can choose the desired shape, material and color. However, this is not the only advantage of homemade ottomans, since its production may cost nothing at all.

Soft poufs

The easiest way is to sew a frameless soft ottoman yourself. To make it, you only need a piece of fabric, stuffing material and sewing machine.

Although if there is none, then it is quite possible to do without it by sewing all the parts by hand. In order for your ottoman to be smooth and look beautiful, you need to make a pattern out of paper. It should be a square with triangles at the ends.

Using this template, you need to cut out 8 identical pieces of fabric, not forgetting to leave seam allowances. Moreover, you can use either one piece of fabric or materials of different colors and textures for each of the parts cut according to the pattern.

After all the parts are ready, you need to stitch them together to form a shape similar to a ball. And in order for the ottoman to be stuffed, bend the top of the triangle of each of its parts inward.

Filler

In order for the pouf to keep its shape, padding polyester or foam rubber are well suited. But other materials can also be used. Even fabric scraps are suitable as such.

To give the ottoman a finished look, you need to close the remaining hole by sewing on a circle of material with processed edges. If it is difficult for you to process the edges of a round-shaped part, then it can be cut into an octahedron shape.

You can simplify the task and sew a pouf from two round parts, which will be the top and bottom of the product, and two rectangular parts, which will be the sides of the pouf.

The height of the ottoman can be adjusted by the width of the rectangle. But the length should always be equal to half the length of the cut circle.

By sewing rectangular pieces, stitching a circle to them and filling them with filling, you can get a round ottoman that will be soft and light. It will become not only a practical piece of furniture, but also a wonderful toy for children that cannot be injured.

A cube-shaped ottoman is made in a similar way. In this case, instead of two rectangular pieces and two circles, you will need 6 squares. Making a cube out of them is not difficult. And if you sew a hidden zipper into one of the edges, you can change the filling and wash the cover.

Pouf made from plastic bottles

You can make an ottoman with your own hands and from plastic bottles. They, of course, must have the same volume.

To do this, the upper part of the bottle, where it begins to narrow, needs to be cut off and the part remaining without a cap must be put on another similar bottle. Repeating this procedure with other bottles, we form them into a round structure.

To ensure that the bottles do not deform and the pouf does not lose its shape, we fasten them with tape.

A little trick is that a bottle located inside other similar ones, fastened with ordinary transparent tape, can be covered with double-sided tape and glued to the inside of the other bottles.

Pay attention!

In order to cover the upper and lower areas, you need to cut a circle out of cardboard or chipboard according to the diameter of the connected bottles. We glue foam rubber to these circles and wrap it around the outside of the pouf.

All that remains is to sew a cover for the finished ottoman. You can sew a zipper around its upper part.

Such furniture will save filler. And if the cover is made of raincoat or water-repellent fabric, then such furniture can even be placed outdoors.

In addition, as can be seen in the photo, round ottomans, made without a frame and containing plastic bottles inside, are practically no different in appearance.

Pouf with lid

In order to make a pouf similar to those sold in stores, you need carpentry skills and some tools. To begin with, you should cut out 4 rectangular pieces from chipboard, 33 cm wide and 40 cm long.

Pay attention!

To fasten them together use wooden blocks. A square with a side of 40 cm is attached to the bottom. As a result, you should end up with a kind of box.

This blank can be sheathed with material from the inside using a construction stapler. The square, which will act as a lid, is also lined with material from below. And the top, before being covered with upholstery fabric, is covered with foam rubber in order to give the ottoman softness.

Along the entire outer perimeter, the pouf, like the lid, is wrapped with foam rubber. And only then they cover it with material. Hinges are used to attach the lid to the cube. To give this piece of furniture mobility, you can attach furniture wheels to the bottom.

It’s even easier to make an ottoman with a lid from a bucket, large saucepan or other utensils and equipment.

The main thing is that, like poufs, they have a removable or opening lid. Then you just need to wrap the workpiece with foam rubber or other soft material and put a cover on it.

All homemade ottomans can fit perfectly not only into the interior of an apartment, but they are also a great option for a summer cottage or outdoor recreation. After all, ottomans are lightweight, mobile due to their size, and comfortable pieces of furniture.

Pay attention!

They are very suitable for children's rooms, giving little ones the opportunity to sit comfortably on them, or even build castles using poufs as blocks.

It is much more convenient to use such a piece of furniture to sit at a low coffee table, because a homemade pouf can be made to any height.

Photo of a do-it-yourself ottoman

A soft and comfortable ottoman can become not just an interesting piece of furniture, but also a practical thing that takes up very little space. Depending on the design style of such a product, it can fit perfectly into any room design. In addition, making and decorating the interior with your own hands is a pleasant activity that will allow you to make it a reality. original ideas for home decoration.

This household item is multifunctional. An ottoman can become a decorative element, serve as a chair, or simply be convenient place for storing small items. And if a frameless option was chosen for its manufacture, it will work well as a toy. There are several options for making an ottoman yourself. Let's look at some of them in more detail.

Tools and materials

This example of work is performed on standard sizes pouf – 400x400x500 mm. To design the product you will need the following:

piano hinges – 2 pcs;
block 150x40x40 mm – 1 piece;
Chipboard with dimensions 1750x2400x16 mm;
upholstery material, 50 mm thick - batting, holofiber, foam rubber or synthetic winterizer;
furniture casters – 4 pcs;
thick fabric for decorative upholstery.

To make a pouf you will need the following tools:

wood glue;
ruler;
wood screws;
screwdriver;
pencil;
construction stapler;
hacksaw with fine teeth;
hammer.

DIY ottoman: step by step guide

Initially, you need to make markings on the working surface. Make the following preparations:

2 rectangular sections 370x400 mm - for the walls of the pouffe;
2 rectangular blanks 370x370 mm - for the side parts;
1 square fragment 400x400 mm.

Then start cutting out the fragments using a hacksaw.
Saw the existing timber into 4 parts so that the length of each is 370 mm.

Assemble a box from all the cut out fragments. The result should be a frame with a height of 370 mm.
Secure the beams with wood glue internal corners designs. This will give it rigidity.
Secure the corners of the frame with self-tapping screws outside. If desired, you can strengthen the structure with metal corners.
Then apply glue to the bottom of the box, as well as to the ends of the beams.
Glue the bottom and let the frame dry.
Then strengthen the structure with self-tapping screws, screwing them into the ends of the box.
Start making the lid. Screw 4 stopper bars along the inner sides of the perimeter.
Make sure that the stiffeners are installed correctly and do not interfere with the lid closing.

12. Then start upholstering the ottoman. In this process, rely on your imagination. As upholstery materials Foam rubber, batting, holofiber or padding polyester are optimal.

13. The product is ready! This ottoman in the interior of your home will not only become decorative element, but also a functional cabinet for storing things.

Ottoman made from plastic bottles

Objects that seem unusual at first glance are suitable as materials for a home ottoman. For example, plastic bottles. This is the most affordable way construction of a home pouf, which is highly decorative and practical to use.

Materials for work

For the workflow you will need the following materials:

bottles with caps - 40 pieces;
scissors;
foam rubber or synthetic padding for lining;
wide tape;
needles and threads;
knitting needles or crochet hook;
yarn;
stapler;
decorative fabric.

Manufacturing process

To build an ottoman from bottles you need to take plastic containers(the lids must be screwed tightly) and using tape, connect them in several layers.
The bottles can be fastened all at once, but for greater strength of the product it is better to fix them in packs of several pieces. And then fasten the resulting sections together again.

3. At the next stage, you need to make a bottom pattern from cardboard. To do this, place a blank with a circumference of 400 mm on the cardboard and trace it with a pencil.

4. Based on the resulting pattern, you need to cut out two blanks.

5. Then place them on both sides of the ottoman and secure with tape.

7. Using a staple gun, nail the foam rubber to the cardboard frame.

8. Foam pads are placed on the product and sewn together.

9. Start sewing the cover. Any thick fabric is suitable for this.

10. On final stage All that remains is to tie the top and sides of the ottoman, which at the end must be sewn to the bottom.

11. The ottoman is completely ready.

Making a spool ottoman

Diversify home environment detail of a classic or rustic style You can make a ottoman sofa using a coil. This option will allow you to make a durable product that can be decorated to your liking. Thanks to this, the pouf will become an original addition to any room interior.

Materials and tools

Before you begin work, you need to prepare the following:

reel made of wood or chipboard;
foam;
glue;
foam rubber or batting;
textile;
cardboard;
construction stapler;
drill;
sewing machine.

Step-by-step manufacturing process

On initial stage you need to cut out parts from foam plastic that correspond to the size of the top part of the coil.
Use glue to fasten them together.
Next, we make a template to work with fabric, batting and foam rubber. To do this, draw a circle on paper, leaving “allowances” for the seams.

We treat the wooden circle with glue and attach the pre-cut circle of foam rubber.

After this, we wrap the structure with cardboard, fixing it with a stapler and adhesive.

Then wrap the pouf with batting and secure it at the bottom with a stapler. Take all the necessary measurements, remove excess pieces and start upholstering with fabric.

After that, we sew a fabric cover and put it on the ottoman. Please note that the decorative upholstery should be taut, but not too tight.
Finally, you should drill holes and attach the legs to the plates.
The work is finished.

Multi-colored fabric ottoman

An ottoman that combines different colors will help fill the interior with colorful shades. Such a household item will allow you to bring it into the overall design of the room. bright accents and make it more original.

Materials for work

To create such an original interior detail, we will need to prepare the following:

pieces of fabric of various but compatible colors;
fabric for lining;
filler material;
needle, thread;
sewing machine;
buttons of a sufficiently large size.

Let's start production

The first step is to create a pattern. To do this, draw a circle with the diameter of the future product. The resulting circle must be divided into parts. First for 4, then each for another 3 fragments.
Using these details, we cut out pieces of fabric in the form of petals, leaving two centimeters for stitching.
We perform the same manipulation with the lining fabric.
The resulting elements need to be sewn on the sides.
Proceed with the construction of the lower part of the future product. It is advisable to use thick fabric for this.
From the wrong side, sew the bottom of the fabric pouf to the top. In this case, you need to leave one “petal” unsewn.
Then you should turn the fabric inside out and fill it with the prepared material.
Sew the product completely.
Conceal the seams with large buttons, sewing them in the center of the ottoman, top and bottom.

Ottoman in the shape of a ball

Bedroom ottomans add variety and complement any decor. In addition, to make this piece of furniture you will need the simplest and most affordable materials.

Preparing for work

To make such an ottoman you need to prepare the following:

polyethylene;
threads with a needle;
sewing machine;
fabric of two colors;
fiber filling material;
graph paper.

Execution steps

Using graph paper you need to make a pattern. Any round object, such as a large ball, is suitable for this.
We measure the circumference of the ball and divide the resulting data by 2.
Then you need to divide the resulting number by 5 so that the 2 outer fragments and 3 parts in the middle are the same size.
At the output we will get the diameter of the circle and the width of the stripes.
Then you should draw a line below based on the resulting width of the parts.
Cut out the bottom from polyethylene. Place it on the first strip and secure the edges with tape.
In a similar way we obtain the part for middle zone. We transfer the received details onto paper.
We make a pattern for the future product from fabric of different colors, leaving 1 cm for the seam.
We sew the parts together, forming uniform stripes.
At the next stage, strips with round parts should be secured in series.
We leave the end of the middle strip unsewn and fill the product with the material prepared for this purpose.
We sew up the remaining hole with an invisible seam.
The ottoman is completely ready for use.

Making an ottoman from a sweater

Enough unusual solution The interior will feature a pouf made from a sweater. This piece of furniture will fit into any home design, especially for decorating a children's room. Let's take a closer look at the DIY ottoman master class.

Materials and tools

To complete this work you need to prepare the following:

old wool sweater;
fabric for sewing a cover;
felt;
expanded polystyrene;
threads;
scissors;
igloo

Step by step instructions

We take felt and cut out a circle of the diameter we need. This will be the bottom of our ottoman.
Then prepare the sweater for work: wrap it in inner side sleeves and sew up the holes.
Next, you need to sew a felt circle to the bottom of the sweater.
The next step is to cut a rectangle measuring 50x70 cm from the fabric.
We sew a cover from it, while making a hem on top. It will serve us as a lace with which we will tighten the neck of the case.
The resulting cover should be placed in a sweater and filled with polystyrene foam.
The last step is to tighten and tie the lace.
The pouf is ready to use.

Conclusion

Of the methods described above for making ottomans, you will surely find the one most suitable for you. Such convenient interior attributes carry not only practical, but also decorative functions. Ottomans with a back or frameless will make your life more comfortable and decorate your home environment. In addition, making your own interior elements is a completely suitable area for creative implementation.

A video tutorial on how to make a pouf with your own hands is presented below:

The topic of this article is how to make an ottoman with your own hands from scrap materials. There are situations when you want to update the interior with some original item and make your own decorative pillows, bean bag chair, ottoman. That's why best way update the interior of your home - do something with your own hands. For example, an ottoman.

It is not always possible to financially purchase fashionable, comfortable and modern ottoman. A homemade ottoman has a number of advantages over store-bought ones. At least in the fact that you can choose for it exactly the colors that you like, combined with color scheme interior and fit perfectly into your environment. Moreover, you can’t always find what you want in the store.
Making an ottoman with your own hands is very easy. For this purpose you will need self-tapping screws, a screwdriver or chisels, a hacksaw, and a hammer. If you want to make a soft ottoman, then take a fabric, preferably bright and colorful, sharp scissors, needles, threads, holofiber, foam rubber or padding polyester and, of course, a sewing machine.

Armed with these items, you can get to work. First, sew an inner cover for the filling (foam rubber, holofiber or padding polyester). To do this, you need thick fabric, from which two circles are cut out, the diameter of which should be approximately 50 cm, or two squares if you want to do it yourself square ottoman. These two geometric shapes will serve as the top and bottom for the future pouf.

Then a strip is cut out of the same material as the base of the pouf. Moreover, its length should coincide with the long circle or the perimeter of the square. As for the width of the strip, it depends entirely on the height of your homemade ottoman. When you cut out the strip, remember to leave some fabric for the seam allowance.

Then we begin to sew the strip on the wrong side: first to the bottom of the ottoman, then to the top. Moreover, you need to start sewing along the length of the strip. After all the seams are ready, turn the ottoman over to the front side, fill it with filling and sew it up. In principle, you can also sew in a zipper, which is much more convenient: for example, for cleaning a pouf or replacing the filling.

All. The basis for your ottoman ready. Now you can start designing it. For those who know how to sew, this will not be difficult. After all, you can not only upholster a pouf with a beautiful and colorful fabric, you can embroider an original pattern with your own hands, for example, create some kind of fantasy ornament, as well as a relief pattern. Anything can be used as a fabric for a cover: jeans, drape, silk and even cotton.

The cover, like the base, is sewn from three parts. First, the side strips are connected, and then the bottom is sewn. As for the upper part of the ottoman, it should be secured with a zipper or buttons. At your discretion. Thus, the ottoman is ready to please the eye and serve as an excellent seat or footstool.

We make a simple but very modern ottoman from cardboard and plastic bottles with our own hands.

How to sew a modern and comfortable ottoman with your own hands. master class with photos of work stages.

Interesting pouf options self made from different materials that you can make yourself.

How to make an ottoman with your own hands without throwing money away? Of course, you can buy it at furniture store, but looking at the cost of a simple chipboard product, there is a desire to do crafts at home. If we consider furniture sets as a whole, then most of them belong to rather complex structures.

You can do something from this list with your own hands experienced craftsmen, and only the ottoman is made without special skills and knowledge from improvised means. A practical item will be obtained when you choose a durable and high-quality upholstery fabric that can be wiped, cleaned, and washed.

Such materials include leather or furniture fabric sold in specialized stores. All that remains is to view step by step instructions for the manufacture of ottomans of various shapes.

So:

An ottoman for seating several people is comparable in height to an armchair and more like a soft bench. For the home, such a model is inconvenient and unnecessary, but in fitting and waiting areas it is very relevant.
An ottoman in addition to something with a certain height. From the definition itself it becomes clear that it does not act an independent product, but serves as an application. Models that barely rise above the floor are not intended for sitting on, but are used as footrests for adults. Children love these miniature things and enjoy using them in their games.
Complementing armchairs, sofas, beds, sliding under the table or as a component in a non-standard combination (beach cabin with pouf), ottomans firmly occupy a niche in furniture showrooms. One can say more, there is a fashion for designer items that make the interior fashionable, complementing it.
The video in this article introduces poufs with advanced features. Looking through it, you remember the plot of the film, when “with a slight movement of the hand, trousers turn into shorts,” and here the ottoman transforms into a full-fledged chair with a table, a bed with a lamp stand and other necessary items, while taking up a minimum of space.

Before you start making an ottoman with your own hands, you need to have an idea about this seemingly simple furniture family.

So, poufs are classified according to materials, design, functions and shapes:

Soft products use textiles, leather. It’s nice to throw your legs on a hand-knitted ottoman, and when the size allows, you can lounge on it.
Rigid ottoman designs are made from rattan, wood, often varnished, bark cork trees . Hard ottomans, made with your own hands, are not suitable for long-term sitting, but they bring liveliness and intrigue to the interior.

Attention: An ottoman is definitely a necessary thing, and its need is felt when entering the house, or rather, the hallway.

How to make, sew, knit and what design of an ottoman to choose is not an easy task. Ottomans can have exposed frames made of steel tubing or wood.
The ottoman may have a closed frame, and the legs are hidden under the frills of a decorative skirt. Such products are popular among the British and Americans.
Ottoman with barely visible legs when a chair is copied without armrests and backrest.
DIY ottoman with back- not only comfortable chair for members of the whole family, regardless of body weight, but also an excellent support for a sore back.
What could be simpler than an inflatable ottoman?, consisting of a textile cover with a zipper and an inflatable chamber inside it? Ottomans differ not only in materials and designs, but also in shape.
DIY square ottoman, round, triangular, combined from different geometric shapes, can be made from available materials.

Tools at home

How to make an ottoman yourself if you don’t have the skills or desire to saw, cut, or twist? Craftsmen offer a lot of ideas and proposals that are brought to life. The work of making a cute ottoman is not difficult, but quite exciting, and a thing made with your own hands radiates a special warmth and has an aura of home comfort.

Soft ottomans

The most simple circuit How to make a soft ottoman with your own hands is as follows:

Two circles are cut out of fabric with a diameter equal to the diameter of the upper and lower parts of the product.

Tip: When cutting out parts, remember to leave seam allowances.

Two rectangular parts of the same size are cut out:

width of the height of the pouf;
length, equal to half the circumference of the top and bottom of the pouf.

Rectangular parts are sewn together on one side along the width to obtain a long ribbon.
One of the circles is basted to it and sewed along the seam.
The same is done with the second circle.

Tip: If the seam is not too even or neat, it is trimmed with a decorative border.

The resulting pouf cover is stuffed with any suitable material.
A zipper is sewn into the unstitched edges remaining in the rectangular tape.

The photo shows a diagram of how to make a pouf in the simplest way.

In a similar way, you can make an ottoman in the shape of a cube. The difference is in making the pieces, which must be square in shape, and to make the sides you will need to make four pieces of fabric rather than two.

Then:

The details fit together.
To more clearly indicate the edges of the cube, you can use a canvas of a different contrasting color.
A denser fabric will provide additional strength and elasticity.
Such a pouf can be filled with padding polyester and foam rubber. These materials hold their shape perfectly and do not deform.
The hole for stuffing the material is made at the bottom of the pouf so that it is not visible.
If desired, you can stitch it tightly after stuffing the pouffe, or sew in a zipper to make it possible to replace the material if necessary.

Sewing an ottoman

The video in this article demonstrates the procedure for sewing an 8-piece ottoman. To do this, a sheet of paper is folded in four, a template is drawn on it and cut out according to the diagram below.

The unfolded template is fixed on the fabric and the cutting of 8 pieces begins.

Attention: It is not necessary to purchase new fabric for the pattern; you can use old deposits of knitted clothing and old sweaters.

The photo below shows that the sharp end of each hexagon is bent inward by approximately 5-6 cm and stitched on a machine, which makes it possible to obtain an octagonal hole for stuffing the finished product after assembling all the elements.

The blanks are attached to each other in pairs with a distance of approximately 1 cm from the edge. The pairs are folded front side In order for the seams to turn out from the wrong side, the stitched form has 4 segments from 2 blanks.
In the same way, they are sewn together in 2 sections and you get 2 halves of the future ottoman.
The halves are machined together and the cover is turned right side out.
The ottoman is stuffed with prepared filling (holofiber, foam rubber, padding polyester), and the hole is closed with a lid of the appropriate size. The edges of the lid should already be finished, and it is manually, carefully sewn on top of the stuffing hole.
The instructions for beginners recommend sewing an ottoman with literally three seams. Why cut out 2 circles, the diameter of which is about 50 cm, or 2 squares, if you prefer clear lines. Geometric shapes will serve as the top or bottom of the future product.
A strip of the same material or another is cut out in a size corresponding to the length of the circle or the perimeter of the square; the width of the strip depends on the height of the ottoman. The height of the ottoman, in turn, is selected depending on the function that the product will perform, whether it is a footrest, a seat in the hallway, a toy for young children, or a structure in the living room.

Attention: The cutting of the strip for the side of the ottoman is done taking into account seam allowances.

The work is done in such a way that the seams are on the wrong side, the strip is sewn first of all to the bottom of the product and only then to the top.
After stitching all the seams, the ottoman is turned right side out and stuffed.
Using the same patterns that are presented above, covers for the ottoman with a zipper are cut out for the first option and for the second. This will allow you to wash or clean the cover in the future without unnecessary problems and time-consuming, and without having to solve the problem of how to cover the ottoman with fabric if it is already made of fabric.

Reliable base for plastic bottles

There are unlimited quantities of plastic bottles in every home. Take, for example, beer and water bottles with a capacity of 1.5 - 2 liters; their color in the finished product does not matter, and they will help unload debris in the yard and house.

To make a good, stable ottoman you will need at least 16 1.5 liter bottles or 9 2 liter bottles.
Cardboard packaging from household appliances also waits its turn and is not thrown away for years, but what if the refrigerator breaks down, how do you take it for repairs? The video in this article will show how cardboard is used to make an ottoman from plastic bottles.

You need to stock up on tape, foam rubber and upholstery material.

Hot glue gun, zipper for case.

Attention: From round bottles you can make an even larger circle, square or rectangle, that is, the shape of the product is chosen according to your preferences.

For ease of use, if a very large ottoman is planned, the bottles are connected into separate sectors and sections with tape, and then the formation of the overall structure begins.

If the future product is planned to be round in shape, then the ottoman should be made starting from the middle.
To do this, take a bottle and, using radial movements, attach new elements to it, which are carefully fixed to each other with tape.
After completing the circle, cut out the base from thick cardboard. It should be slightly larger in size than the bottle structure.

The cardboard is also secured with several layers of adhesive tape. There is no need to dwell once again on the point that 2 bases must be prepared, and everything is clear.
It's your turn soft upholstery, for which two parts for the top and bottom are cut out of dense foam rubber, which are glued in place.
From the remaining part of the foam rubber, according to the dimensions of the circumference line of the side part, a rectangle is cut out, which is wrapped around the pouf.
The final stage of sewing the cover from furniture fabric, preferably with a zipper. This operation will not only allow you to easily remove the cover for washing, but also make several options and update from time to time appearance of your product.

Ottoman from grandma's rarity

How to make an ottoman out of a stool so that grandma’s rarity can serve for many more years?

Indeed, a well-knitted stool made of durable wood, painted oil paint, may please the owners for many years, but the appearance does not correspond to the modern environment. Remodeling will help bring balance to the interior old stool in a stylish ottoman.

The stool structure is first strengthened with self-tapping screws.
The legs are shortened a little - do not forget to check the level so that the ottoman does not wobble later.
The frame of the future ottoman is assembled using 4 sheets of plywood. They are attached with self-tapping screws to the legs of the stool.
The fifth sheet of plywood is screwed from below and serves as the bottom of the future craft.
The foam for the seat is cut out with an allowance of 5 cm.

Attention: Upper part The ottoman is coated with glue, then the foam rubber will not form an untidy lump over time.

The upholstery fabric on the seat is attached together with the foam rubber using staplers.
Foam rubber can be attached to the sides with slats, which help to give round shape ottoman and make it more beautiful.
The rest of the structure is covered with fabric and secured with staples.
The wheels are screwed on or, as in the photo above, the cute little legs of the updated stool peek out from under the flirty upholstery.
The problem of how to make an ottoman from a stool was solved in a short time.

For those who like to knock

The rich Russian language raises many associations and questions. How to knock, where to knock, when to knock? For those who like to hit a nail with a hammer, we suggest making an ottoman with your own hands from boards and chipboard.

Rectangular pieces of 40x30 cm from chipboard are pre-prepared in the amount of 4 pieces.
A circle with a diameter of 30 cm and wooden blocks 4 pieces.
Wood glue.
Furniture wheels with special fasteners.
Metal corners, self-tapping screws.
Foam rubber and upholstery fabric.

How can you see the set? necessary materials not much different from each other when we make an ottoman with our own hands, even in different ways:

A box is assembled from rectangles. They're on the move metal corners, self-tapping screws, all corners of the structure are aligned, they must be straight.
The bars on which the wheels will later be located are fixed with glue on the lower part.
A base is attached to the top in an individually selected shape.
The finished frame is upholstered using the same technology using foam rubber, fabric and a zipper on the cover.

For lovers of knitting and stuffing

How to make an ottoman with your own hands that is frameless and therefore soft. Needlewomen who know how to crochet will be able to knit a soft ottoman much faster, but not everyone may like their appearance.

Women who like to work with knitting needles present interesting models of ottomans knitted with knitting needles:

To work, you will need the thickest knitting needles that are available in stores.
For knitting needles with a diameter of 9 mm, fairly thick wool is suitable.
Ordinary threads offered in stores are too thin. The price for them is not high, but due to the fact that you will have to make thicker ones out of them, weaving them together, you will have to purchase enough large number, which will add to the cost of the product.
You can, of course, cut, loosen, twist unnecessary knitwear, which takes a lot of time, and even to find at home required quantity plain knitted clothing that has become unusable is quite problematic.
It seems that the solution to the problem of how to make an ottoman with your own hands has reached a dead end, but cotton clotheslines caught my eye.

Attention: Synthetic clotheslines are not suitable for this job, and cotton ropes are difficult to buy in small towns.

For a soft ottoman of sufficient size, you will need 20-30 of these ropes, which are tied into a long rectangle.
The side is tied together with rope to create a spacious, wide skirt.
The bottom is tied with a rope of the same color and you get a bag that needs to be stuffed with something. There are 2 options here - use old items neatly stacked on shelves in the closet or go to the store and buy foam rubber or holofiber.

Unnecessary old items make the ottoman heavy and not as round and fluffy as those made from store-bought materials, but it frees up space in the closet for new clothes.
The top of the ottoman is decorated with the same rope and you can try out your product.

Ottoman from an old bucket

Here's another one interesting solution, for which we will need: an old plastic bucket, a thick jute rope, a hot glue gun, a stapler, scissors, a cabinet handle, Velcro tape, upholstery fabric and a few new microfiber cloths. You will also need cardboard, but it will be better if you replace it with thin plywood.

First, wash the bucket and remove the metal handle.

Next, use hot glue to glue outer surface buckets with a rope, starting from the bottom.

Cut the end of the rope and hide it carefully.

Place the bottom of the bucket on the cardboard and trace it. Lay out the upholstery fabric according to the intended template and cut the round blank with a 5-centimeter outlet.

We make a hole in the center of the cardboard and fabric. We pass a bolt from a furniture handle through them and screw on the knob.

Next, we roll the fiber into tubes and radially wrap the bolt between the cardboard and paper, creating a kind of roll. To prevent the fiber from unwinding, we securely fix it with glue.

Then the fabric is stretched and secured on the reverse side with a stapler.

To hide cardboard marks, close reverse side seats with another piece of fabric that needs to be placed on glue.

Cut the Velcro into four equal to the segment and stick them crosswise onto the bottom of the bucket and the base of the saddle - with the bristles towards the bucket, and the fluffy part towards the seat. Connect the two parts. Hooray! The ottoman is ready!

The result is such a useful craft that you can sit on comfortably.

Various options provide the opportunity to solve the problem of how to make an ottoman yourself from scrap materials, which are available in abundance in any home. The only thing I still wanted to focus on was the floor in the room.

Laminate is quite sensitive to mechanical stress, so it is better to make an ottoman without wheels and legs, that is, with a solid bottom. On soft covering, carpet, ottomans on casters are appropriate, but for tile covering there are no restrictions, except forged legs can be an exception.

Chipboard ottoman

In one toast, the hero of “Prisoner of the Caucasus” expressed the very essence of existence, so that “our desires coincide with our capabilities.” If you have free time and a desire to make an ottoman with your own hands from chipboard, you need to prepare the possibilities.

Tools and necessary materials stocked up in advance.

A good ottoman cannot be made without a good base made from a sheet of chipboard. Optimal size the design is within the range of 400x400x500 mm.
You can make a wooden ottoman using a simplified technology, making a frame in the form of a mailbox from a timber and screwing it on with the side cuts, but since the ottoman is being made for yourself, you can try.

Work with pleasure

WITH bad mood You should not take on the work: something will fall on your foot or you will hit the wrong nail with a hammer.

5 squares of 400x400 mm are marked and cut from a sheet of chipboard to make the walls of the structure and the bottom.

Attention: The bottom of the ottoman should not be made of plywood; small children like to hide in secluded corners and can break the thin plywood and get injured.

The cover can be any geometric shape: square, round, oval. Beginners can skip experimenting and stick with a square lid. It will have dimensions slightly larger than the main box 430x430 mm, in order to protect it from falling inside.
The height of the finished product is made up of its constituent elements - the height of the structure is 400 mm, plus the rollers are 50 mm, the bottom and tire are 32 mm thick, the upholstery is 50 mm thick, for a total of 532 mm.
From the prepared elements, the formation of the structure begins.
The sides of the ottoman are fastened with metal corners. The beams that glue all the internal corners will help increase rigidity and reliability.
From the front side of the ottoman, the cutouts themselves are screwed into the beams, the heads of which should be recessed into the wood so that later there are no problems with torn upholstery.
The lower part of the box is coated with wood glue along the perimeter, capturing the ends of the beams.
The bottom of the ottoman is attached, and the cuts themselves are again screwed into the ends of the beams. Assembled structure should dry well.
The base of the ottoman has been made, but there are still no wheels and a lid on which you can sit in the future.
The lid is secured with 4 bars screwed from the inside. The work is carried out after you are sure that the lid closes smoothly and the side reinforcement bars do not interfere with the closing of the lid.
The finished structure is turned over, and the wheels themselves are attached with the cuts.

Attention: They are fixed through the bottom to the ends of the beams, for which small holes are drilled in the bottom.

Before continuing work, you need to make sure that the resulting structure is sufficiently stable, holds the person sitting on it well and there are no shortcomings that would interfere with further work, otherwise there is no point in starting the upholstery.

The ottoman gets dressed

A do-it-yourself ottoman made of wood, chipboard, or generally soft needs clothing on top. This function is performed with honor by high-quality upholstery fabric, neatly attached to the frame of the structure.

First, the cover of the ottoman is made, for which a soft lining is cut out from foam rubber, padding polyester, and batting. The size of the pad must correspond to the parameters of the seat so that it is neatly glued into place without drooping.
From the fabric intended for upholstery, a blank is cut out several times large sizes than the lid. This is done so that the edges can be folded under the lid and secured from the inside with a stapler or furniture nails.
The instructions instruct you to further design the sides of the ottoman.
The part is cut out from upholstery fabric 400 mm x 4 = 1600 mm with a margin for connection. Also in height, the material must have an allowance at the top and bottom.

Attention: The fabric must be straightened, stretched, tucked inward, and the edges must be secured with furniture nails or a stapler.

The seat is decorated, the niche is upholstered, all edges are carefully closed, and the finished product can be presented to discerning family members for inspection.
A do-it-yourself plywood ottoman is made according to the same pattern if you choose this simple design option.
The work becomes a little more complicated when an opening drawer is provided on the ottoman, then the stop bars are replaced with door hinges.

Getting acquainted with the design of this simple piece of furniture, one detail catches your eye: despite the difference in shapes of ottomans and their types, the base is a rigid frame, there is a seat and legs. They are decorated in different ways, but quilted leather or leatherette gives the products an elite, luxurious look and you cannot immediately determine that the price of the product is within reasonable limits.

Although, it should be noted that a neat ottoman, covered with a different material, can bring comfort and convenience to the room and looks no less elegant than a leather one.

How to make an ottoman with your own hands without throwing money away? Of course, you can buy it in a furniture store, but looking at the cost of a simple chipboard product, you will want to do crafts at home. If we consider furniture sets as a whole, then most of them belong to rather complex structures.

Experienced craftsmen can make something from this list with their own hands, and only the ottoman is made without special skills and knowledge from improvised means. A practical item will be obtained when you choose a durable and high-quality upholstery fabric that can be wiped, cleaned, and washed.

Such materials include leather or furniture fabric sold in specialized stores. All that remains is to look at the step-by-step instructions for making ottomans of various shapes.

So:

An ottoman for seating several people is comparable in height to an armchair and more like a soft bench. For the home, such a model is inconvenient and unnecessary, but in fitting and waiting areas it is very relevant.
An ottoman in addition to something with a certain height. From the definition itself it becomes clear that it is not an independent product, but serves as an application. Models that barely rise above the floor are not intended for sitting on, but are used as footrests for adults. Children love these miniature things and enjoy using them in their games.
Complementing armchairs, sofas, beds, sliding under the table or as a component in a non-standard combination (beach cabin with pouf), ottomans firmly occupy a niche in furniture showrooms. One can say more, there is a fashion for designer items that make the interior fashionable, complementing it.
The video in this article introduces poufs with advanced features. Looking through it, you remember the plot of the film, when “with a slight movement of the hand, trousers turn into shorts,” and here the ottoman transforms into a full-fledged chair with a table, a bed with a lamp stand and other necessary items, while taking up a minimum of space.

Before you start making an ottoman with your own hands, you need to have an idea about this seemingly simple furniture family.

So, poufs are classified according to materials, design, functions and shapes:

Soft products use textiles, leather. It’s nice to throw your legs on a hand-knitted ottoman, and when the size allows, you can lounge on it.
Rigid designs of ottomans are made from rattan, wood, often varnished, or the bark of cork trees.. Hard ottomans, made with your own hands, are not suitable for long-term sitting, but they bring liveliness and intrigue to the interior.

Attention: An ottoman is definitely a necessary thing, and its need is felt when entering the house, or rather, the hallway.

How to make, sew, knit and what design of an ottoman to choose is not an easy task. Ottomans can have exposed frames made of steel tubing or wood.
The ottoman may have a closed frame, and the legs are hidden under the frills of a decorative skirt. Such products are popular among the British and Americans.
Ottoman with barely visible legs when a chair is copied without armrests and backrest.
DIY ottoman with back- not only a comfortable chair for members of the whole family, regardless of body weight, but also excellent support for a sore back.
What could be simpler than an inflatable ottoman?, consisting of a textile cover with a zipper and an inflatable chamber inside it? Ottomans differ not only in materials and designs, but also in shape.
DIY square ottoman, round, triangular, combined from different geometric shapes, can be made from available materials.

Tools at home

Soft ottomans

The simplest diagram of how to make a soft ottoman with your own hands is as follows:

Two circles are cut out of fabric with a diameter equal to the diameter of the upper and lower parts of the product.

Tip: When cutting out parts, remember to leave seam allowances.

Two rectangular parts of the same size are cut out:

width of the height of the pouf;
length equal to half the circumference of the top and bottom of the pouf.

Rectangular parts are sewn together on one side along the width to obtain a long ribbon.
One of the circles is basted to it and sewed along the seam.
The same is done with the second circle.

Tip: If the seam is not too even or neat, it is trimmed with a decorative border.

The resulting pouf cover is stuffed with any suitable material.
A zipper is sewn into the unstitched edges remaining in the rectangular tape.

The photo shows a diagram of how to make a pouf in the simplest way.

Then:

The details fit together.
To more clearly indicate the edges of the cube, you can use a canvas of a different contrasting color.
A denser fabric will provide additional strength and elasticity.
Such a pouf can be filled with padding polyester and foam rubber. These materials hold their shape perfectly and do not deform.
The hole for stuffing the material is made at the bottom of the pouf so that it is not visible.
If desired, you can stitch it tightly after stuffing the pouffe, or sew in a zipper to make it possible to replace the material if necessary.

Sewing an ottoman

The video in this article demonstrates the procedure for sewing an 8-piece ottoman. To do this, a sheet of paper is folded in four, a template is drawn on it and cut out according to the diagram below.

The unfolded template is fixed on the fabric and the cutting of 8 pieces begins.

Attention: It is not necessary to purchase new fabric for the pattern; you can use old deposits of knitted clothing and old sweaters.

The photo below shows that the sharp end of each hexagon is bent inward by approximately 5-6 cm and stitched on a machine, which makes it possible to obtain an octagonal hole for stuffing the finished product after assembling all the elements.

The blanks are attached to each other in pairs with a distance of about 1 cm from the edge. The pairs are folded with the front side so that the seams are on the wrong side; when sewn, there are 4 segments of 2 blanks.
In the same way, they are sewn together in 2 sections and you get 2 halves of the future ottoman.
The halves are machined together and the cover is turned right side out.
The ottoman is stuffed with prepared filling (holofiber, foam rubber, padding polyester), and the hole is closed with a lid of the appropriate size. The edges of the lid should already be finished, and it is manually, carefully sewn on top of the stuffing hole.
The instructions for beginners recommend sewing an ottoman with literally three seams. Why cut out 2 circles, the diameter of which is about 50 cm, or 2 squares, if you prefer clear lines. Geometric shapes will serve as the top or bottom of the future product.
A strip of the same material or another is cut out in a size corresponding to the length of the circle or the perimeter of the square; the width of the strip depends on the height of the ottoman. The height of the ottoman, in turn, is selected depending on the function that the product will perform, whether it is a footrest, a seat in the hallway, a toy for young children, or a structure in the living room.

Attention: The cutting of the strip for the side of the ottoman is done taking into account seam allowances.

The work is done in such a way that the seams are on the wrong side, the strip is sewn first of all to the bottom of the product and only then to the top.
After stitching all the seams, the ottoman is turned right side out and stuffed.
Using the same patterns that are presented above, covers for the ottoman with a zipper are cut out for the first option and for the second. This will allow you to wash or clean the cover in the future without unnecessary problems and time-consuming, and without having to solve the problem of how to cover the ottoman with fabric if it is already made of fabric.

Reliable base for plastic bottles

There are unlimited quantities of plastic bottles in every home. Take, for example, beer and water bottles with a capacity of 1.5 - 2 liters; their color in the finished product does not matter, and they will help unload debris in the yard and house.

To make a good, stable ottoman you will need at least 16 1.5 liter bottles or 9 2 liter bottles.
Cardboard packaging containers from household appliances also wait their turn and are not thrown away for years, but what if the refrigerator breaks down, how to take it for repairs? The video in this article will show how cardboard is used to make an ottoman from plastic bottles.

You need to stock up on tape, foam rubber and upholstery material.

Hot glue gun, zipper for case.

Attention: From round bottles you can make an even larger circle, square or rectangle, that is, the shape of the product is chosen according to your preferences.

For ease of use, if a very large ottoman is planned, the bottles are connected into separate sectors and sections with tape, and then the formation of the overall structure begins.

If the future product is planned to be round in shape, then the ottoman should be made starting from the middle.
To do this, take a bottle and, using radial movements, attach new elements to it, which are carefully fixed to each other with tape.
After completing the circle, cut out the base from thick cardboard. It should be slightly larger in size than the bottle structure.

The cardboard is also secured with several layers of adhesive tape. There is no need to dwell once again on the point that 2 bases must be prepared, and everything is clear.
Now it’s the turn of the soft upholstery, for which two parts for the top and bottom are cut out of dense foam rubber, which are glued in place.
From the remaining part of the foam rubber, according to the dimensions of the circumference line of the side part, a rectangle is cut out, which is wrapped around the pouf.
All that remains is the final stage of sewing a cover made of furniture fabric, preferably with a zipper. This operation will allow you not only to easily remove the cover for washing, but also to make several options and update the appearance of your product from time to time.

Ottoman from grandma's rarity

How to make an ottoman out of a stool so that grandma’s rarity can serve for many more years?

Indeed, a well-built stool made of durable wood, painted with oil paint, can delight its owners for many years, but the appearance does not correspond to the modern environment. Remaking an old stool into a stylish ottoman will help bring balance to the interior.

The stool structure is first strengthened with self-tapping screws.
The legs are shortened a little - do not forget to check the level so that the ottoman does not wobble later.
The frame of the future ottoman is assembled using 4 sheets of plywood. They are attached with self-tapping screws to the legs of the stool.
The fifth sheet of plywood is screwed from below and serves as the bottom of the future craft.
The foam for the seat is cut out with an allowance of 5 cm.

Attention: The upper part of the ottoman is coated with glue, then the foam rubber will not bunch up into an untidy lump over time.

The upholstery fabric on the seat is attached together with the foam rubber using staplers.
Foam rubber can be attached to the sides with slats, which help give the ottoman a round shape and make it more beautiful.
The rest of the structure is covered with fabric and secured with staples.
The wheels are screwed on or, as in the photo above, the cute little legs of the updated stool peek out from under the flirty upholstery.
The problem of how to make an ottoman from a stool was solved in a short time.

For those who like to knock

Rectangular pieces of 40x30 cm from chipboard are pre-prepared in the amount of 4 pieces.
A circle with a diameter of 30 cm and 4 wooden blocks.
Wood glue.
Furniture wheels with special fasteners.
Metal corners, self-tapping screws.
Foam rubber and upholstery fabric.

As you can see, the set of necessary materials does not differ much from each other when we make an ottoman with our own hands, even in different ways:

A box is assembled from rectangles. Metal corners and self-tapping screws are used, all corners of the structure are aligned, they must be straight.
The bars on which the wheels will later be located are fixed with glue on the lower part.
A base is attached to the top in an individually selected shape.
The finished frame is upholstered using the same technology using foam rubber, fabric and a zipper on the cover.

For lovers of knitting and stuffing

Women who like to work with knitting needles present interesting models of ottomans knitted with knitting needles:

To work, you will need the thickest knitting needles that are available in stores.
For knitting needles with a diameter of 9 mm, fairly thick wool is suitable.
Ordinary threads offered in stores are too thin. The price for them is not high, but due to the fact that you will have to make thicker ones out of them, weaving them together, you will have to purchase a fairly large quantity, which will add to the cost of the product.
You can, of course, cut, unravel, and twist unnecessary knitwear, which takes a lot of time, and finding the right amount of plain knitted clothing at home that has become unusable is quite problematic.
It seems that the solution to the problem of how to make an ottoman with your own hands has reached a dead end, but cotton clotheslines caught my eye.

Attention: Synthetic clotheslines are not suitable for this job, and cotton ropes are difficult to buy in small towns.

For a soft ottoman of sufficient size, you will need 20-30 of these ropes, which are tied into a long rectangle.
The side is tied together with rope to create a spacious, wide skirt.
The bottom is tied with a rope of the same color and you get a bag that needs to be stuffed with something. There are 2 options here - use old items neatly stacked on shelves in the closet or go to the store and buy foam rubber or holofiber.

Unnecessary old items make the ottoman heavy and not as round and fluffy as those made from store-bought materials, but it frees up space in the closet for new clothes.
The top of the ottoman is decorated with the same rope and you can try out your product.

Ottoman from an old bucket

Here is another interesting solution for which we will need: an old plastic bucket, thick jute rope, a hot glue gun, a stapler, scissors, a cabinet handle, Velcro tape, upholstery fabric and a few new microfiber cloths. You will also need cardboard, but it will be better if you replace it with thin plywood.

First, wash the bucket and remove the metal handle.

Next, using hot glue, glue the outer surface of the bucket with rope, starting from the bottom.

Cut the end of the rope and hide it carefully.

Place the bottom of the bucket on the cardboard and trace it. Lay out the upholstery fabric according to the intended template and cut the round blank with a 5-centimeter outlet.

We make a hole in the center of the cardboard and fabric. We pass a bolt from a furniture handle through them and screw on the knob.

Next, we roll the fiber into tubes and radially wrap the bolt between the cardboard and paper, creating a kind of roll. To prevent the fiber from unwinding, we securely fix it with glue.

Then the fabric is stretched and secured on the reverse side with a stapler.

To hide the cardboard marks, cover the back of the seat with another piece of fabric, which needs to be placed on glue.

Cut the Velcro into four equal pieces and stick them crosswise onto the bottom of the bucket and the base of the saddle - with the bristles towards the bucket and the fluffy part towards the seat. Connect the two parts. Hooray! The ottoman is ready!

The result is such a useful craft that you can sit on comfortably.

Laminate is quite sensitive to mechanical stress, so it is better to make an ottoman without wheels and legs, that is, with a solid bottom. On soft surfaces, carpet, ottomans on casters are appropriate, but for tiled flooring there are no restrictions, unless forged legs can be an exception.

Chipboard ottoman

Tools and necessary materials are stocked in advance.

A good ottoman cannot be made without a good base made from a sheet of chipboard. The optimal size of the structure is within 400x400x500 mm.
You can make a wooden ottoman using a simplified technology, making a frame in the form of a mailbox from a timber and screwing it on with the side cuts, but since the ottoman is being made for yourself, you can try.

Work with pleasure

You should not start work in a bad mood: something will fall on your foot or you will hit the wrong nail with a hammer.

5 squares of 400x400 mm are marked and cut from a sheet of chipboard to make the walls of the structure and the bottom.

Attention: The bottom of the ottoman should not be made of plywood; small children like to hide in secluded corners and can break the thin plywood and get injured.

The lid can be made in any geometric shape: square, round, oval. Beginners can skip experimenting and stick with a square lid. It will have dimensions slightly larger than the main box 430x430 mm, in order to protect it from falling inside.
The height of the finished product is made up of its constituent elements - the height of the structure is 400 mm, plus the rollers are 50 mm, the bottom and tire are 32 mm thick, the upholstery is 50 mm thick, for a total of 532 mm.
From the prepared elements, the formation of the structure begins.
The sides of the ottoman are fastened with metal corners. The beams that glue all the internal corners will help increase rigidity and reliability.
From the front side of the ottoman, the cutouts themselves are screwed into the beams, the heads of which should be recessed into the wood so that later there are no problems with torn upholstery.
The lower part of the box is coated with wood glue along the perimeter, capturing the ends of the beams.
The bottom of the ottoman is attached, and the cuts themselves are again screwed into the ends of the beams. The assembled structure must dry well.
The base of the ottoman has been made, but there are still no wheels and a lid on which you can sit in the future.
The lid is secured with 4 bars screwed from the inside. The work is carried out after you are sure that the lid closes smoothly and the side reinforcement bars do not interfere with the closing of the lid.
The finished structure is turned over, and the wheels themselves are attached with the cuts.

Attention: They are fixed through the bottom to the ends of the beams, for which small holes are drilled in the bottom.

The ottoman gets dressed

First, the cover of the ottoman is made, for which a soft lining is cut out from foam rubber, padding polyester, and batting. The size of the pad must correspond to the parameters of the seat so that it is neatly glued into place without drooping.
From the fabric intended for upholstery, a piece is cut out that is somewhat larger in size than the lid. This is done so that the edges can be folded under the lid and secured from the inside with a stapler or furniture nails.
The instructions instruct you to further design the sides of the ottoman.
A part is cut out from upholstery fabric 400 mm x 4 = 1600 mm with a margin for connection. Also in height, the material must have an allowance at the top and bottom.

Attention: The fabric must be straightened, stretched, tucked inward, and the edges must be secured with furniture nails or a stapler.

The seat is decorated, the niche is upholstered, all edges are carefully closed, and the finished product can be presented to discerning family members for inspection.
A do-it-yourself plywood ottoman is made according to the same pattern if you choose this simple design option.
The work becomes a little more complicated when an opening drawer is provided on the ottoman, then the stop bars are replaced with door hinges.

Although, it should be noted that a neat ottoman, covered with a different material, can bring comfort and convenience to the room and looks no less elegant than a leather one.