We will send the material to you by e-mail
Wallpapering is an important part of any renovation. This process is labor-intensive and complex. Many people are interested in: how to glue vinyl wallpapers on paper basis. In this case, it is important to choose high-quality glue, since if you use a low-quality composition, everything will need to be finished again. Features of gluing depend on the selected material. Vinyl panels are popular because they are characterized by reliability, wear resistance and resistance to ultraviolet radiation. Before you purchase a material, you should find out the features of working with this material.
Finishing with fabrics on vinyl based provides an opportunity to use unusual design techniques
Pasting consists of the following steps:
Helpful information! There should be no drafts in the room. The canvases will dry within two days.
Related article:
The ceiling surface must be glued before gluing the walls. In this case, it is worth choosing lighter materials.When processing the ceiling, you should remove all items and carpets. If items cannot be taken out, they are covered with plastic wrap.
For your information! Vinyl is a great conductor of electricity, so it is important to remove any exposed wires.
Corners require special care. When until corner zone If the distance remains less than the sheet, the sheet is cut with an overlap. This part will shift to a perpendicular wall surface. Then the second layer is glued with an overlap. The sheets are passed with a special roller.
The drying time of the canvas depends on the dryness of the working surface and temperature values. If the humidity is exceeded and the temperature is slightly reduced, the finish will take a long time to dry.
Also, the drying time depends on the type of glue, the amount of solution used and the microclimate in a particular room.
Non-woven surfaces can dry within 24 hours, while paper surfaces can dry in less time.
Helpful information! When drying, the canvas with a paper base can shrink significantly, so you need to make sure that the seams do not move out.
Using vinyl wallpaper you can create a stylish and original interior. When choosing a texture and pattern, you should use original design solutions and various combinations.
Save time: selected articles delivered to your inbox every week
Before you start gluing vinyl wallpaper, you need to find out what this material is. They produce wallpaper based on non-woven or paper. The material is dense, has a non-standard and varied texture, and allows you to hide many wall defects.
Externally, vinyl wallpaper for walls is truly chic, but when wet, it tends to stretch in width, so you shouldn’t spread it heavily with glue. Although there is a second option, when only the wall is treated with glue, leaving the wallpaper dry. These points are indicated in the instructions from the manufacturer.
When gluing the strips, you need to carefully press them to the surface, removing bubbles and irregularities. They are glued end to end, overlap is not allowed. The wallpaper is too thick and the edges will be too obvious. You need specialized glue, designed specifically for vinyl wallpaper.
When purchasing, you should take into account the fact for which room the vinyl wallpaper is intended. If this is a kitchen, then embossed ones are not recommended, because patterns can accumulate dust. It is optimal to choose smooth ones - if they become dirty, they can be wiped damp cloth.
Silk-screen printing is suitable for pasting the living room and bedroom. Its surface is protected from fading, so the original color will remain for many years. It is recommended to glue in active rooms, for example in the hallway. They are durable, wear-resistant, and easy to wash.
Before gluing vinyl wallpaper, the surface must be carefully prepared:
Important! Wallpaper should be glued in closed room, drafts are unacceptable. Therefore, it is worth closing the windows and turning off existing appliances (air conditioning or fan). It is not recommended to paste new wallpaper over old ones.
If the wallpaper was not checked when purchasing, you should check the entire batch before you start cutting it. Pay attention to the numbers (they must match), pattern and color. If everything fits, you can open the first roll.
After measuring the height, the canvas is cut. To cut wallpaper with a pattern, the stripes must be aligned and only then cut to size. If the ceiling line is uneven, the strips are cut with an allowance of several centimeters.
The adhesive intended for vinyl-based wallpaper differs in composition from other adhesives. It contains impregnation that protects wall coverings from fungus.
Once prepared, it can be stored for 10 days. During the drying process, a light transparent film forms on it. The glue does not harm human health. Has good adhesion.
When diluting the adhesive composition with water, pay attention to the instructions and proportions, mix well and let the glue swell. Apply the mixture evenly to the wallpaper and leave for 5 minutes to allow it to soak in better. When applied Special attention you need to pay attention to the joints - if there is not enough glue, they can separate after drying.
Wallpaper sticker on walls
According to the instructions, you should start gluing the first strip from the window. You should carry out gluing work with a partner. One, standing on the stairs, applies the top edge of the canvas to the wall under the ceiling. The second one, standing below, supports the end of the canvas and aligns the edge with a vertical line previously drawn along the wall.
The strip is pressed against the wall and, using a brush, any air bubbles are removed. Do this from top to bottom, moving from the center to the edges of the strip. If the glue comes out beyond the edges, you can wipe it off with a clean rag. The excess allowance at the bottom is carefully cut off with a knife.
It is strictly not recommended to combine two canvases in a corner. To properly cover a corner, you should stick a single strip and overlap the corner by up to 5 centimeters. The joints are pressed tightly to the surface for a strong adhesion.
Correctly pasting vinyl wallpaper behind the radiator should be up to a depth of 20 centimeters. To make it easier to press them, use a narrow roller with a long handle. Alternatively, you can paint the wall behind the radiator in a color identical to the color of the wallpaper.
If the plinth was not dismantled during the work, then when gluing the strip, its end is inserted into the gap between the plinth and the wall. If the allowance is too long, it should be trimmed. But ideally, the skirting boards are first removed and installed back after gluing.
Before pasting, you should turn off the power to the room and remove the switches and sockets in the room. When gluing the strips, marks are made at the locations of the electrical points. After the glue has dried, these places are carefully cut, after which the sockets and switches are installed in place.
Home renovation is a troublesome business, especially when it comes to... interior decoration, which sets the tone for the entire interior. The presence of errors can ruin the entire design of the room. We will help you avoid them by examining in detail how to glue vinyl wallpaper to the ceiling and walls.
First, let's pay a little attention to the selected material. Why vinyl wallpaper, what's special about it? Everything will become quite clear after reviewing their quality characteristics.
The products in question are a non-woven or paper base covered with a layer of vinyl.
This structure provides them with many advantages:
The only thing that can happen unpleasantly after applying the wallpaper in question is the presence unpleasant odor the first two months. But this is subject to the condition of purchasing cheap samples from an unknown manufacturer. High quality models do not have such an effect.
Advice: if you end up gluing foul-smelling canvases, and even airing doesn’t help, then it is recommended to paint them with acrylic paint.
The polymer layer will block the contact between vinyl and air, eliminating the spread of odor.
First of all, you should prepare everything necessary for finishing work.
To work you will need:
Tip: choose a staircase that has a shelf on top.
Then you will have somewhere to put the container with glue.
Tip: before gluing heavy vinyl wallpaper, be sure to make sure the prepared brush is sufficiently rigid.
Because soft bristles will simply crumple against dense fabrics and will not cope with their task.
In addition to the tools, you need to take care of the materials themselves:
Before gluing vinyl wallpaper, you must carefully prepare the wall surface.
And although such large-scale work with perfect alignment, as in the case of using paint, are not required, something still needs to be done:
Now let's figure out how to glue vinyl wallpaper:
We have looked at how vinyl wallpaper is glued. The process is absolutely not complicated, but it requires care and attention. Follow all the above recommendations and you will succeed.
The video in this article will provide Additional information. Good luck with your wallpapering!
Are you trying to figure out how to properly glue vinyl wallpaper? They have their own characteristics in application and, knowing them, the gluing process will not be difficult. Washable vinyl wallpaper - very convenient and practical wall material. They are moisture resistant, easy to remove dirt from, and contain special antifungal components.
Those who have decided to insulate their balcony or loggia and comfortably decorate and equip this new room can safely recommend the use of this material. Correctly selected wallpaper will not only give the balcony a pleasant appearance, but will also last a long time.
Once you have decided which type you will use, you can begin to calculate the required amount of wallpaper and all the necessary materials.
One of the proven and reliable methods of calculation required quantity rolls of wallpaper is to determine the perimeter of the floor and the height of the room. To do this, you need to add up all the sides of the floor and multiply the resulting number by the height of the room. Then subtract from this the area of the window and doorways and divide the remainder by the area of one roll. Round the final number up - you have received the number of rolls that will be needed to cover a specific room.
If implemented gluing vinyl wallpaper with a picture, then additional calculations will be needed to adjust the image. An important concept here is the pattern pitch - the distance separating two identical images along the length of the roll. The difficulty is that the actual step may differ from this figure, since you will be gluing the right and left parts.
Please note: to avoid complications, add 5 cm per strip in 10 cm increments. The amount of waste in this case will be equal to half a step from each strip.
Once you have calculated how many rolls of wallpaper you will need, you can estimate how much glue will be needed. Don't blindly trust what is written on the package. The amount of glue for vinyl wallpaper is determined on the basis that a pack of 250 g is enough for an average of 20-25 square meters. Sometimes the flow rate may exceed these parameters.
You picked suitable wallpaper, determined how much material will be needed. Next, prepare everything necessary tools. In the process of preparing the room and when gluing vinyl wallpaper, we use:
Now you have stocked up with everything you need. Familiarize yourself with the topic, and you can begin the actual process.
Vinyl wallpapering completed.
The most difficult and painstaking work is finishing small details and gluing corners and joints. To avoid troubles in the form of gaps and pronounced seams, glue the pieces of wallpaper overlapping. For vinyl wallpaper on a non-woven basis it is 1-2 mm, on paper - up to 5 mm. The issue of gluing the corners is somewhat more difficult to resolve.
This is the most the hard part work: question, how to glue corners, often confuses, especially beginners. When starting this stage, coat the corner thickly with glue. It is better to cut the canvas so that it overlaps the adjacent walls by 2-3 cm.
If you measured the angle using a level and found that it is very “overwhelmed,” use the trimming method. Glue the first piece in exactly the same way, only leave the edges wider - about 9 cm. Place the side strips strictly vertically (the same level will help with this) at a distance of 2 cm. Cut the overlap with a sharp knife - both layers together. And then glue it back upper layer.
After all the main stages of work have been completed, check how you installed the vinyl wallpaper. Check to see if there are any un-glued areas or bubbles on the walls. Replace previously removed sockets and switches. If there are any radiators, radiators or other devices in the room, behind which there are hard-to-reach areas of the wall, then you can not paste them over, but simply paint them in a color similar to the wallpaper.
Have you become familiar with the how to properly glue vinyl wallpaper, and found out that even on balconies and loggias they can be used as wall decoration. If this article helped you make repairs, then leave your comments. Or perhaps you have your own secrets for wallpapering? Please share your unique experiences. Your advice can be very useful to many people.
Below are photographs on the topic of the article “How to properly glue vinyl wallpaper: step by step instructions" To open the photo gallery, just click on the image thumbnail.
We also invite you to watch the video on the topic of our article. This video shows how to properly glue vinyl wallpaper.
Did you like the article? Subscribe to site updates via RSS, or stay tuned:
In contact with , Facebook , Classmates , Google Plus or Twitter.
Subscribe to updates by E-Mail:
Tell your friends! Tell your friends about this article in your favorite social network using the buttons in the panel on the left. Thank you!
Discuss the article
To the post “How to properly glue vinyl wallpaper: step-by-step instructions” 10 comments
The first time I needed to install vinyl wallpaper in my apartment, I was slightly shocked. How to work with them?! But after reading the articles and studying all the intricacies, wallpapering was not as terrible as I initially thought it would be. The most important thing in this matter, in my opinion, is to prepare the wall well for wallpaper. It should be clean (without any traces of the old coating) and even.
And I was just very disappointed for the first time after gluing vinyl wallpaper, since I didn’t know all these subtleties and glued this together with my husband. On the second day, the two of us simply gasped, the joints were generally bristling. So for me the joints and corners turned out to be big problem, and the second time they hired a specialist. It’s a pity that I didn’t come across such an article earlier.
Recently I hung vinyl wallpaper on non-woven backing in village house. Of course, they hide the unevenness a little, but I had to tinker with the joints for a very, very long time. Due to the fact that the walls are a bit uneven wallpaper They go either butt to butt or overlap. Where the joint is joint - everything is fine, even the seam is practically invisible. But that’s where the overlap is where it’s a problem. The wallpaper does not want to stick together, so the top layer sticks out very much. Maybe this is due to the fact that the wallpaper is thick.
We always glue wallpaper at home ourselves. It always turns out differently. My husband and I often argue about how to properly hang wallpaper. After reading the article, we learned many of the intricacies of this difficult matter. It was useful to know the stages of work; we understood our mistake, that we did not have the correct organization and did everything wrong. Now we will glue strictly according to your recommendations.
I was looking for similar instructions I’ve been online for a very long time, and thank you very much for laying out everything step by step. My husband is on a business trip and I had to do this “fun” thing myself - gluing wallpaper. the business is not easy, but there were children helpers nearby (although they are 5-6 years old)) and a fighting spirit) I’ll start with the fact that choosing wallpaper is very difficult, firstly, finding a quality product at a reasonable price is not always easy , secondly, to match the interior so that your eyes don’t get tired in a year or two - sometimes you don’t have enough patience, and pleasing all family members in terms of color and design is not an easy task. in general, we dealt with this quickly, but how to glue them, if you don’t call a team... if I hadn’t found the video and photos, I would hardly have taken up this task. For me the most difficult thing was: gluing the corners. if it weren’t for your site, it would have been just “corner hell”, since I had absolutely no idea how, what and where. thanks a lot! in general, my wallpaper was glued in 3 days)) with my own hands) so I feel like a heroine)) everyone is happy, thanks to you))
When we hung vinyl wallpaper in a private house, the “first pancake” was a huge lump! But... the Internet is here to help, and after learning a lot of problems from this article, we took the risk of painting another room ourselves! A nice tip was to apply an antifungal agent to the walls. I hope the walls won't grow mold. But it still took a lot of work to glue the corners correctly! But we did it! Now we have experience in gluing and the next rooms are not so scary. I would like to put up photo wallpaper in the living room. I think we will succeed now!
Now is the time to change the decor in your apartment or create comfort in a new home.
Have you chosen vinyl wallpaper for wall decoration, but don’t know how to hang it?
Then it’s time to figure out what tools are needed for this and how to do it correctly at home.
Before you start gluing, you need to decide what kind of wallpaper you want to hang in a particular room, since there are several types and varieties.
foam, flat, silkscreen, polyfoam and rigid vinyl, or as they are called washable.
As for their safety in the house where we live, think for yourself, the material from which they are made is PVC, these are the same plastic windows, linoleum, suspended ceilings.
I would not recommend gluing them in children's rooms, and carefully choosing a manufacturer that guarantees quality and environmental friendliness.
To know how to glue vinyl wallpaper with your own hands, you will have to collect a small set of tools (they are not specific and can be found in any household) and acquire some skills, which I will describe in detail in this article.
So, let's start with the tool that we will need in the process of wallpapering.
When everything you need has been collected, we begin preparatory work.
The first thing to do is remove old paint and the pieces are not removed wallpaper and peeling putty. After this, we prime the walls and fill the cracks with putty.
When everything is dry, prime the walls with a primer, or wallpaper glue, in the proportion that you will find on the glue box. Typically the ratio is 1:8 (glue:water). A primed wall will absorb less glue and the wallpaper will adhere more firmly.
First of all, prepare the glue according to the manufacturer's instructions.
We take into account that no matter what glue you use, no matter how you prepare it, you will need 45 grams of ready-made solution for 1 m² of vinyl wallpaper.
How could it be without special effort glue wallpaper, namely vinyl?
Firstly, there are several types of vinyl wallpaper, and the choice of adhesive and method of its application depend on their type, and the manufacturer usually indicates this information on the wallpaper packaging in the form of icons.
Before you start gluing, exclude any drafts in the room until the wallpaper is completely dry, otherwise they will decorate your floor until the morning!
When we reach the corner, measure the distance from the edge of the glued wallpaper to the corner and add an overlap of 2 cm, cut off such a strip from the whole panel. We glue this strip with an overlap at the corner.
We glue the next panel overlapping into the very corner. Next we glue strips of vinyl wallpaper along old scheme- butt.
If you remember, when preparing the wallpaper panels, we made overlaps under the ceiling and on the floor. Be sure to trim these overlaps using a spatula and stationery knife under the ceiling and near the floor.
We change the blade of the knife according to the degree of its dullness - do not skimp on this, otherwise the knife will simply tear the wallpaper.
Before gluing, switches and sockets must be removed, the electricity must be turned off to avoid electric shock, and the wallpaper must be glued on top of them. We cut out the holes for them when the wallpaper is dry and then we install everything in place.
In principle, this is probably all you need to know in order to cover a room with vinyl wallpaper correctly.
Good luck to everyone in this simple matter!
