To properly care for an acrylic bathtub, you need to purchase soft sponges and microfiber cloths. Also, when cleaning, it is necessary to use special products that will not harm the acrylic surface, which is quite specific in responding to the effects of aggressive agents. chemicals. Find out more about cleaning this bathtub below.
Foam creates a thin protective layer that prevents dirt from settling on the surface of the bathtub.
In addition, if there is no home special means, you can use dishwashing gels, as well as washing powder, previously dissolved in water.
But before you start treating the bath with this product, you need to know how it’s done:
In addition to cleaning the surface, Domestos reliably disinfects it and creates a protective layer.
To prevent plaque from stagnating, it is necessary to clean the bathtub with these products at least 2 times a month. If measures are not taken in time, then over time the thin hard film will thicken. Each time it becomes more and more difficult to remove it from the surface of an acrylic bathtub.
An acrylic bathtub has a number of advantages over similar products made of cast iron or steel.
And although heavy cast iron baths, coated with enamel, are more durable; knowledge of how to care for acrylic sanitary ware will allow you to extend their service life for a long time.
Wear-resistant acrylic, used in bathroom equipment, is a type of durable and impact-resistant plastic. However, the material can easily be damaged by improper care.
To clean the surface from dirt and all kinds of deposits, do not use hard metal sponges or abrasive powders. The main danger for acrylic is contact with sharp objects, which can damage the integrity of the coating and leave deep scratches. So, below you can find out what to wash with acrylic bathtub and how often can this be done so that the surface is clean and at the same time not damaged.
Important: Do not bathe pets or wash, for example, kitchen utensils in a bathtub made of acrylic fiber. If there is such a need, it would be good to lay a thick rubber mat on the bottom.
It is necessary to constantly monitor the cleanliness of the acrylic bathtub surface. After all, it is much easier to regularly and quickly wash off the stains that appear than to then scrupulously scrub off stubborn islands of dirt.
It is recommended to use good cleaning products with active ingredients on average once every 2 weeks. In this case, the detergent is evenly distributed over the entire surface of the bath, left for a few minutes, and then thoroughly washed off with water.
Advice: if the plumbing has a hydromassage system, it must be washed at least once a month. Important condition: It is allowed to use only gentle disinfectant components in the composition.
As mentioned above, in order not to scratch the surface, you need to remove dirt and plaque exclusively with mild means. It could be normal liquid soap, leftover shampoo or dishwashing gel. Speech in in this case It’s about daily care: immediately after taking a bath, soap its surface, rinse off the foam with warm water, and use a sponge to clean the entire container until it shines.
The instructions for the bathtub usually contain a list of approved detergents that will help remove stains from its surface if necessary. Most often, such substances in their release form are a spray or gel in a bottle with a dispenser. So, for example, the well-known “Silit Beng” has the inscription “suitable for acrylic” on the label, but there is no such inscription on “Domestos” or “Pemolux”. So be sure to read the instructions (on the manufacturer’s website it is available with a video).
Advice: If matte areas appear on the initially glossy surface of the bathtub, this is a sign that the coating has been damaged. It can be restored using a special acrylic primer.
Before using chemicals, it would be correct to make sure that there is no chlorine and ammonia, acetone, aggressive acids and alkalis in its composition. If these components get on the bottom and walls, they damage the integrity of the coating and aesthetic appearance plumbing fixture: white acrylic may turn yellow in places.
The most common problem that owners of acrylic bathtubs and showers encounter is yellowing. This happens for several reasons:
Accordingly, remove yellow plaque follows, focusing on the factor of its appearance. In the first case, you need to review your arsenal of detergents and eliminate the use of those that harm the surface. In the second, add a small amount of a special softening component to the water. Third, systematically use bleach.
Advice: It is not necessary to use a means of mass production from the chemical industry. The usual one copes well with yellowness. lemon juice(rub the surface, leave for 8 hours, rinse with warm water, wipe dry soft cloth). Besides this The best way disinfect the bath before bathing the baby.
In case of lack of trust in industrial means, regularly clean acrylic surfaces from plaque and return them to their radiant White color folk secrets will help.
You can wash the bathtub from yellow stains and stubborn rust using not only lemon juice, but also citric acid. To do this you need:
Important: Bathing a baby in an acrylic bathtub with potassium permanganate is a bad idea. You shouldn't do this! Brown plaque is guaranteed, and washing it out will not be so easy. It is better to use a special baby bath for these purposes.
Due to the hard water supplied by the water supply system, a specific gray coating may appear on the acrylic bathtub - the so-called water stone. You can remove it and bleach plumbing fixtures with ordinary vinegar.
A solution of soap and soda can handle the vast majority of common stains. It is applied to the stains for 20-30 minutes, then washed off with water and, as in previous methods, you must remember to thoroughly wipe the surface with a dry cloth.
If you want to get the effect with the “super” prefix when cleaning acrylic from rust stains, the best option will use a mixture (1:1) of hydrogen peroxide and ammonia. Use a sponge with liquid to blot the stain; as soon as the result appears, you need to thoroughly wash the previously problematic area with water and wipe it dry with a cloth.
Important: Never clean your bathtub with baking soda – scratches are inevitable! Only soda solution can be used.
Whitening can certainly remove tough stains from different surfaces. But at the same time, you need to remember that this product is very aggressive for such a delicate sanitary ware and you cannot clean the bathtub with it. The danger of using it is that after several cleaning procedures, the acrylic coating becomes very porous. As a result, dirt, rust and salt deposits settle in these places “tightly”, the surface of the bathtub deteriorates to such an extent that it is often beyond repair. Also, chlorine causes yellowness, which is extremely undesirable for any housewife.
So you have learned how to safely clean an acrylic bathtub, both purchased and folk remedies. One or more of them is sure to be found in every woman’s household.
Acrylic bathtubs are a good alternative to heavy cast iron and quickly cooling steel ones. These products are not subject to corrosion and contain special antibacterial components that block the growth of fungus and mold. With care and the right approach to the sink, such plumbing fixtures can serve their owners for a long time without fading and pleasing the eye with their bright whiteness.
The new acrylic bathtub looks impeccable, shines white and clean. It is pleasant to take water procedures in it. To she retained its shine longer, it is necessary carefully use it and follow it rules of care behind an acrylic bathtub at home.
The primary task is the competent selection of cleaning composition, taking into account the type of contamination. There are many detergents that can be used to wash an acrylic bowl at home to obtain a shiny surface.
Rust that appears should be dealt with immediately when it is detected. It penetrates into the structure of acrylic and is difficult to remove with household chemicals. Don't delay cleansing.
How to wash an acrylic bathtub from rust:
It is not enough to remove red spots. Get rid of the reason for their formation. Most often these are old taps and mesh at the bottom of the bathtub. If they are not replaced, rust will appear again and again.
In the fight against limescale, the most important thing is to choose the right tactics. Otherwise, you’ll say goodbye not only to mineral deposits, but also to your plumbing.
How to clean a bathtub from limescale? For these purposes, they buy professional preparations Sanfor, Gel WC 5+, RAVAK Turbocleaner.
How to clean a bathroom:
Sanfor, Gel WC 5+ and RAVAK Turbocleaner cannot be used for cleaning metal parts. Work with compounds wearing protective gloves.
Cleaning productslime with acrylic won't hurt surface. Their effect on acrylic is regularly tested.
Acrylic turns yellow because of bad water, sudden temperature changes. The material loses its whiteness, if the owners dry the bathtub after reception water procedures.
And save the bowl from yellow stains? Hydrogen peroxide, laundry bleach and apple cider vinegar will help remove stains.
How to clean an acrylic bathtub:
There are still many folk remedies, how to remove yellowness from an acrylic bathtub. But this is not enough. It is necessary to install a heating radiator in the room in winter before drawing water. Wipe it well surface must be perfectly dry.
Many professional compositions have been developed to care for acrylic bathtubs. They are used according to the manufacturer's instructions for dosage and cleaning methods.
What is the best way to clean a bathtub? acrylic coating Anyone who has decided to purchase plumbing fixtures made from this material must know.Buy special cleaning products from trusted manufacturers.
How to clean an acrylic bathtub:
All liquids are applied with a sponge and left for some time (usually 5–20 minutes, detailed instructions see label). After using professional chemicals, rinse thoroughly bath
Over time the bath becomes dull. She becomes not as radiant as before. There are good home methods to help restore whiteness.
How to clean an acrylic bathtub at home? You can whiten the surface citric acid, baby soap or toothpaste.
How to whiten an acrylic bathtub at home:
Home methods are not as effective as professional formulations. Several applications are needed to achieve the desired result.
Sometimes diligent cleaning ends in trouble. On a surface baths scratches appear. This occurs due to the use of abrasive substances to cleanse contaminants.
How to remove abrasions, scratches and chips:
If you find damage, repair it immediately. Dirt quickly penetrates into scratches. It's hardly pleasant to swim in such a bath.
Don't ignore these rules. This will help save your plumbing from damage.
How to wash an acrylic bathtub at home and some useful tips:
Acrylic bathtubs differ from other sanitary ware in their dirt-repellent effect. But If not properly cared for, the surface loses its “sales appearance”.
Cleaning compositions should be selected depending on the frequency of use, type of contamination, and water characteristics.
The acrylic surface needs to be kept clean regularly. Follow cleaning instructions, tips and care recommendations. This will preserve the beauty of the bowl and its shine for many years.
A clean and sparkling bathroom is the pride of any housewife. However, keeping it in perfect order requires a lot of effort. This is especially true for apartments or houses where large families live.
When purchasing an acrylic bathtub, many housewives are sure that it must be washed exclusively with special, expensive products. However, practice shows that this is not at all the case. In our article we will tell you how to wash an acrylic bathtub at home. From the options listed, you will surely find an effective and rational option, suitable for you.
Previously, bathtubs were made of cast iron or steel, so they were heavy and massive, which did not suit all consumers. Acrylic bathtubs appeared on modern market plumbing is relatively new and has the following advantages:
To begin with, we suggest you understand the techniques and methods that absolutely cannot be used for cleaning an acrylic bathroom. If you want the product to serve you faithfully for many years, remember the means that are strictly prohibited when disinfecting:
Never try to clean the surface of an acrylic bathtub with pure chlorine or chlorine-containing products! Instead of a glossy and uniform shiny surface, you will get cloudy bathtub walls. If you re-treat an acrylic surface with chlorine, you will get a bathtub riddled with small pores into which dirt will constantly clog.
Everyone knows that abrasive particles easily scratch any surface, including acrylic. Naturally, scratches and damage can be rubbed out and polished, but in the case of a curved bathtub surface this will be a very problematic task.
With prolonged use of ammonia solutions, acrylic gradually deteriorates, and the surface from glossy becomes matte and unaesthetic.
These are the products that can quickly ruin the acrylic surface, making it cloudy and unattractive. And with prolonged exposure, solvents, like ammonia, corrode acrylic.
In modern everyday life, formaldehyde-based products are no longer used, but just in case, it is important to know about their incompatibility with acrylic coatings.
To prevent global contamination, it is enough to rinse the enamel after taking a bath. hot water or a soft sponge with regular soap. Tip: If you treat polished acrylic enamel with hot water, the surface will shine even more!
The main rule: no brushes or rough steel wool! All detergents must be applied only with soft rags or sponges without an abrasive surface. Helpful advice: Before trying out a new cleaning product, try testing it on an inconspicuous area of your bathtub. Wait 10-15 minutes: if there are no negative changes, feel free to start cleaning.
You should be careful when disinfecting acrylic bathtubs, because without special care, pathogenic harmful microorganisms accumulate in the nozzles and pipes. The main thing is not to use chlorinated solutions! Specialized products also often contain chlorine, but its effect is smoothly neutralized by other components.
Important: to keep the bathtub enamel shiny, rub the acrylic in a circular motion using a soft cloth dipped in wax-based polish.
Sooner or later you will have to face different types contaminants, so you need to be prepared to quickly eliminate them. Let's list the most common ones:
Acrylic is a type of plastic (polymer) and has high performance characteristics. Unlike steel bath, the material does not rust or peel off, and is also not afraid of water: even dirty, hard or very hot.
Polymers do not support the active use of household chemicals, and the use of non-household chemicals is completely excluded. How to deal with pollution? It is necessary to use an active medium that is not capable of reacting with the surface. These include citric acid and vinegar.
However, using them in pure, undiluted form is dangerous, unlike aqueous solutions.
Acrylic bathtub cleaning solution
In stores today there are a lot of specialized products that can be used to remove lime or rust deposits. But if you don’t want to overpay, we recommend listening to advice on how to wash an acrylic bathtub at home + from limescale.
Acid solutions perfectly remove water stone and limescale at home, which many products cannot cope with.
Acrylic enamel is susceptible not only to dirt, but also to scratches of varying depths. At the same time, acrylic is in some way a unique material, because how easily it is scratched, so easily these scratches are then removed.
To remove minor enamel damage (up to 0.5 mm deep), take a piece of ordinary felt and polish the surface. If the scratches are pronounced and deep, they can only be eliminated with liquid acrylic. In this case, there is no need to call a specialist: it is enough to purchase a kit for repairing acrylic bathtubs, consisting of a plastic spatula and a tube of liquid acrylic, which is applied to the damage. After drying, the application area is polished with felt.
Liquid acrylic can even seal a through hole. To do this with outside bathtubs are glued with tape and the space is filled with acrylic in several stages.
Sometimes the damage and contamination are so severe that an acrylic bathtub can only be saved with the help of special liners, which are sold in plumbing stores.
Remember: acrylic is afraid of exposure high temperatures! Therefore, even the ash from a cigarette will leave a noticeable stain.
Treat your acrylic bathtub with care and caution, then acrylic sanitary ware will serve you for many years!
Relatively recently, bathtubs made of acrylic, a plastic previously widely used in dentistry, have entered the ranks of sanitary products. The variety of shapes, strength and hardness, and antibacterial qualities contribute to the popularity of such plumbing fixtures. But since composite material Quite capricious when it comes to detergents, it’s worth finding out in advance how to clean an acrylic bathtub and how to do it correctly.
In order not to spoil the sanitary ware, it should be taken into account that the polymer is sensitive to cleaning powders with abrasives and aggressive chemical solutions. Before you start treating the bath, carefully study the composition of the product and instructions for its use. The following is a list of chemical products that are not recommended for acrylic care.
Acrylic plumbing fixtures should not be cleaned with concentrated alcohols, alkalis, or acids: they cause small cracks and discoloration of the bathtub.
Important: When caring for a plastic bathtub, do not use hard metal scourers or brushes. It is best to clean acrylic with a soft sponge or rag. Too hot water is also dangerous for plastic: it can cause deformation of the tank.
Experienced housewives advise: before starting the procedure and cleaning the acrylic bathtub, you should test the product yourself. To do this, squeeze it onto your hand and “palp” it: there should be no sharp crystals in the preparation.
Another testing option is to apply a small amount of detergent to an inconspicuous area of the surface. If after use appearance coating has not deteriorated, treatment can be carried out over the entire area. But it’s still better to buy special preparations that guarantee that their use is safe for acrylic, or delicate universal means for cleaning.
It is important to properly care for your acrylic bathtub to extend its service life. These days, there are many products that can be used to clean an acrylic bathtub. Here is a list of the most effective developments from well-known manufacturers.
Its popularity is explained by its speed of action and versatility: the drug helps remove residual detergents, get rid of rust, mold, and salt deposits. "Acrilan" does not damage the surface of the bathtub - on the contrary, it becomes glossy due to the creation of a thin protective film.
The line includes several products, each of which performs its own function: cleaning, disinfection, restoration of the protective layer.
The brand is represented by a line of drugs from the manufacturer Koipa. In addition to cleaning gels, it includes products for restoring and polishing the bathtub.
This is an environmentally friendly product without harmful ingredients. The drug gently disinfects the surface, eliminates odors, removes salt deposits and greasy stains.
A universal spray or cream suitable for all types of coatings and plumbing fixtures. Due to the absence of abrasives, Sif is safe for acrylic surfaces. With its help, you can wash the bathtub from yellowness, rusty streaks, grease, and lime.
This liquid composition ideal for daily care.
An effective spray, when using which you have to wear a respirator due to the characteristic pungent odor.
A universal cleaner suitable for bathtubs and other sanitary fittings. Gently cleans acrylic of fat and rust spots, traces of soap. The formula of the drug contains a polymer that prevents the growth of fungus and the adhesion of dirt.
Having solved the problem of choosing a cleaning product, all that remains is to clean the bathtub. Usually the instructions can be found directly on the packaging.
The general rules for using household chemicals at home are as follows:
How can you clean an acrylic bathtub if you can’t use household chemicals? The choice of option depends on the nature of the contamination.
A weak solution of citric acid will help get rid of limescale (instead, you can add 1.5 liters of table vinegar to the bath). Taking a bath hot water(temperature up to +50 o C), add 50 g of lemon, leave for several hours to soften salt deposits. Drain the working solution and rinse the surface with running water. Finally, remove any remaining moisture with a soft cloth.
The yellowed bottom and walls of the bath are bleached with apple bite, lemon juice or citric acid (20 g per glass of water). The problem areas are wiped with liquids, and after a few minutes they are rinsed with a stream of water under pressure. The surface is blotted with a dry cloth.
Rusty stains are cleaned with soda. Water is first added to the powder. The resulting paste is applied to the “reddened” areas (no need to rub) and washed off after 10-15 minutes.
Deeply ingrained dirt can be removed using toothpaste without abrasive particles. Her in small quantity squeeze it onto a cloth and wipe the stains with it.
You can also wash the bath using folk remedies. Special acrylic bathtubs for hydromassage procedures are equipped with nozzles (sprayers) connected to circulation pump. He creates overpressure water, which then comes out with pressure through the small holes of the sprayers in a given direction. If moisture remains on the injectors, this causes mold growth, the proliferation of microorganisms, and the formation of a layer of lime deposits.
What and how best to clean hot tub? The cleaning and disinfection process is combined, carried out in several stages:
