Installation of polystyrene foam tiles requires a minimum of tools, time and additional materials, therefore, the fastest and least labor-intensive type of ceiling finishing is an adhesive ceiling. Expanded polystyrene tiles are divided into three types according to the production method: stamped, injection and extruded.
This is the simplest and cheap look products, it is made from polystyrene foam on stamping machines at elevated temperatures. Stamped tiles have the most disadvantages: they are fragile, crumble when broken, and are difficult to clean. But since the adhesive ceiling is practically not subject to mechanical action, this drawback can be ignored. After carefully gluing the tiles and letting them dry, you can paint them with water-based paint. acrylic paint in any color, and then, if necessary, update with new paint.
Prices for stamped tiles range from 39 rubles and above, but usually do not exceed 55 rubles. By successfully choosing a pattern and color, you can create a good design in a room with a glued ceiling from inexpensive tiles, despite a budget option products.
It is also called injection. It is produced in molds by sintering polystyrene foam, and its quality indicators are higher than stamped tiles. It is produced in white, but after pasting the ceiling it can be painted with acrylic paint.
In addition to the smooth surface, stamped tiles are made with a profile relief. The lower the ceiling in the room, the less voluminous you need to choose the pattern on the tiles, otherwise the ceiling in the room will seem even lower. The cost of the material depends on the density of the polystyrene foam sheet and the complexity of the pattern, and ranges from 59 to 100 rubles.
In this photo, pressed tiles imitating stucco are suitable for spacious rooms, such as a living room.
The most expensive and high-quality ceiling tiles are extruded. Its surface is covered with a thin film (laminated), so the surface of the tile is perfectly smooth, easy to clean and not afraid of minor mechanical loads. Another advantage of such a product is the unlimited choice of colors. It is available in imitation stone, wood, or just a plain color, so you can immediately choose a product of a suitable shade and do not have to carry out additional work on painting the ceiling. The photo below shows an example of extruded marbled tiles.
The protective film on extruded tiles creates a water-repellent effect. Therefore, if you need to make an adhesive ceiling in the kitchen or bathroom, it is better to choose a product with laminated coating, since fumes can accumulate in these rooms.
In addition to lamination, extruded tiles can be factory-painted with waterproof paints, which creates a coating that is not inferior to laminated tiles.
The average cost of 1 m2 of extruded tiles is about 100 rubles. Price for expensive options products with beautiful design And high-quality coating reach 170 rubles per 1m2.
The price of expanded polystyrene ceiling tiles varies significantly among different manufacturers. You can buy inexpensive Omsk tiles Format Lagom from the factory of the same name: price from 39 rubles. The product will cost a little more from the companies VTM Holding from Rostov-on-Don and Nitram from Mytishchi, Moscow region: from 49 to 82 rubles.
Seamless tiles have no edges, and when the sheets are joined, the joints between the tiles are almost invisible and the surface appears as a continuous sheet. Tiles for a seamless ceiling come with a wavy edge, and then its surface is especially beautiful.
But the seamless type of tiles is only ideal for gluing smooth surfaces, since at small differences the edges of the tiles are difficult to join, and they look very ugly. Particularly difficult is covering the ceiling with seamless tiles with a complex relief pattern. Some craftsmen install seamless tiles on a pre-arranged sheathing of even slats, but then the device glue ceiling without seams becomes more complicated and expensive, and sometimes the meaning of its design is lost. If the surface cannot be leveled, it is better to use regular tiles with cut rounded edges.
The standard size of polystyrene foam tiles is 50x50 cm, which means there are 4 square sheets per 1m2. This size makes it easy to count the number of tiles for covering the ceiling. The tiles are sold packaged in 2 m2 packs, that is, 8 pieces per package, but if you need to buy an odd number of m2, you can ask the seller to remove the missing sheets of tiles from the packaging.
Rectangular tiles measuring 100×16.5 cm are also considered standard. It is used mainly as a decorative element and is glued to the wall along the perimeter to finish an already pasted ceiling.
Recently, some manufacturers have begun to produce ceiling tiles in a wider selection of sizes. Products of 60×60 cm, 40×40 cm, 70×40 cm, 70×30 cm and 60×30 cm appeared. By gluing non-standard size tiles in a room, you can visually expand or lengthen the ceiling.
Read also: How to choose ceiling plinth, Ceiling tiles from expanded polystyrene, Buy hanging chair to the ceiling, Self-adhesive PVC floor tiles. Reviews
Repair is an expensive undertaking. In addition, it takes time to completely renovate the interior, which also requires a lot. What to do when resources are limited, deadlines are tightened, and repairs must be carried out, at least temporarily?
You need to choose accordingly inexpensive material, which is easy to use, in front of walls that will happen as quickly as possible.
In this obvious solution, among other things, foam is tiles made of polystyrene foam (expanded polystyrene) on the ceiling. He has obvious advantages described below.
Polystyrene foam
As the name suggests, foam ceiling tiles are made from a lightweight synthetic material such as polystyrene foam.
Its advantages:
In a pinch, the adhesive will suffer, and then only if selected incorrectly.
The market supply will allow you to imitate high-quality plaster.
Like all other building materials, polystyrene foam has many disadvantages that limit its use. These include:
We must rely solely on the fact that no one will do it intentionally, but it is possible to accidentally touch something by accident, but this is very problematic.
Whatever the design on such a board, it is impossible to create a rich interior design. This is the main quality of foam tiles, which makes repairs using temporary ones.
Foam Types
Foam ceilings are classified according to the technology used in its manufacture. Depending on the production method, some characteristics of the tile vary significantly:
A blank is cut out of a large piece of polystyrene foam, from which tiles can be printed using this or another design. The thickness of the finished product is up to seven millimeters, the color is matte white. Its main advantage is that it is inexpensive, which allows them not to be afraid of high costs both when completing and partially replacing tiles. Backsplash tile works well in almost any color. The main disadvantage of this tile is its fragility. Careless handling both during installation and during transportation inevitably causes damage to the material.
Also, in a compressed plate, the edge, if slightly defective, will be very noticeable.
The injection plate is not afraid of moisture and water, but also has good sound insulation properties. On the other hand, greater thickness allows for the creation of an image of great depth, making very small cutting interlocking joints almost invisible.
There is obvious inaccuracy in geometry during installation, so extruded polystyrene ceiling tiles require more care when gluing than any other.
Preparation for gluing tiles
Constructing a ceiling with foam filtration, as already mentioned, is preferable to other materials in the processing process.
This statement also applies to preparatory work, which will not be too spacious and boring.
After all, this latter material hides various cracks, hills, holes and other surface imperfections that do not need to be separated separately.
However, some preparatory work is necessary. If there is chalk or lime on the ceiling, they need to be washed. If all types of clothing are present, they must also be removed. A primer coat is required on the ceiling surface to ensure sufficient adhesion to the adhesive.
For example, you can use a ready-made solution that is sold in any hardware store.
Typically, ceiling tiles are made from different types The foam forms a square, with a side length of 50 centimeters. Before gluing, you must carefully measure each side of the ceiling. Each of them is that the difference between seemingly identical sides can be several centimeters.
If this is not taken into account, the holes in the device will be too high and difficult to repair.
After measuring the ceiling, calculate the number of whole tiles. All partial tile inserts must be carefully measured and cut using cutting tools. Large deviations in such preparatory work are also undesirable; for the same reasons, they can lead to loss of installation quality.
To ensure high accuracy of installation, a line must be marked on the ceiling.
For each tile there is no need to precisely mark the surfaces; it is enough to draw control lines every meter, both along and across. It is then almost impossible to make a significant error.
Ceiling tiles
There is a reference line on the ceiling, the tile is ready, there is glue and tools to use it, you can continue with the installation.
If training is carried out on good level, this level will not cause any special problems.
Polyvinyl acetate adhesive (PVA) or special compounds can be used to glue polystyrene foam boards, for example. Glue "Dragon". They are good if the ceiling surface is completely flat. If there is irregularity hidden only for installation, it is recommended to use a mixture of PVA glue and gypsum in water.
This design holds the tiles securely up to the ceiling, and its label can be adjusted to the height of a specific area.
The gluing technology is more than simple.
The slabs at the edges and in the middle should be expanded with adhesive, placed on the ceiling, aligned along the control lines, along the walls and adjacent plates, and slightly compressed. After pressing it, you need to hold the plate for a minute or two so that the glue has time to reach the surface of the ceiling. Everything must be done with care, remember that foams are very light and can be easily moved from the glued area.
If the tiles do not fit close together, the error can be corrected by using the same PVA adhesive mixed with gypsum solution. After painting, such surface preparation does not matter.
Along the edges is a ceiling covered with expanded polystyrene, usually trimmed with a ceiling leg or, as it is often called, a baguette. The edge of the ceiling is made of the same material as the tiles, so it should be glued together with glue.
The last level of ceiling tile finishing is painted with acrylic or another color.
There are no special technological methods for this. If you do not need to remember the relief surface, which cannot be painted with a roller. To work, use a brush, preferably a small width.
How to seal the seams on ceiling tiles yourself?
To be honest, it is not entirely clear from the question which tile we are talking about.
If it’s tiled, then that’s one thing; if it’s made of foam (or foam-like) material, then that’s another. I will focus on both options.
Tile: The seams are grouted in the same way as on the walls or floor. With exactly the same grout, I recommend using Ceresit grout, it has an excellent consistency, plus a huge selection of colors, you can choose which one suits you best.
Grout tiles, begins with cleaning the seams from tile adhesive, I use a specially sharpened screwdriver for this purpose.
The seams have been cleaned, we dilute the grout, the grout should be a little thinner than sour cream, this will fill all the seams better.
Of course, there are special spatulas for grouting (rubber), you can work with them, you can also use iron ones, but sometimes they leave streaks, in general you need to see the tile.
We wipe the seams after about ten minutes, I advise you to use furniture foam rubber, it does not shatter into small pieces and smoothes the seams perfectly, change the water more often, you can pour used water into a sewer with a diameter of 100 mm, but not with a diameter of 50 mm.
The tile has dried, now wipe it with a dry cloth.
The last piece of advice on this topic: Don’t spread a lot of grout, try to grout a couple of squares, not all at once, although the ceiling in the bathroom (if we’re talking about this room) has a couple of squares, a little more, up to 2.5, that’s more accurate).
If the tile is made of polystyrene foam, then you bought an extremely low-quality material, such a tile is glued into the joint and there simply should not be any seams on it.
If, nevertheless, you become the owner of a low-quality material, then there is a way out; I suggest gluing such tiles onto white silicone, firstly damp room silicone is better than any putty, and secondly, you can seal (whiten) the seams with the same silicone.
When working with silicone, use a “gun” and a damp cloth; wipe off excess silicone almost immediately.
First, we clean the seams from glue or anything else they are filled with.
The seams must be deepened by 3-5 mm, otherwise the grout layer will not last long. We dilute the grout in water in small portions and apply it to the tiles with a rubber spatula, trying to completely fill all the seams.
Let the grout set a little and after about 15 minutes wash it off with a sponge and big amount water. After we have washed it for the first time, we take the plastic socket from the dowel nail and draw it at the same angle along all the seams, evenly deepening them. After you wash the tiles again, you can wipe them dry, I use the second option if the tiles are glossy, fine particles The grout polishes the tile well.
5336 10/02/2019 7 min.Foam tiles are often used to finish the ceiling surface. Among the others facing materials This tile is significantly better in price. As a result, we get a beautiful solid canvas that imitates stucco, literally for pennies. For low-budget renovations - the most the best option. And foam ceiling tiles have many other advantages. However, there are also disadvantages.
The quality of the finished foam ceiling surface depends on the materials used (tiles, glue), as well as on the installation method and the accuracy of the craftsman. Also common. As a rule, such material has original designs or ornaments. Today we offer a wide range of these tiles, among which you can find several varieties:
Despite the slight differences between, in general, general pros and cons of foam products can be noted.
As you can see, foam tiles have many advantages. In addition, the panels can be glued to almost any surface, even directly onto whitewash.
Small unevenness on the ceiling is allowed. The tile is very flexible, which allows it to adhere tightly to the surface with minor imperfections. However, it is necessary to mention some of the disadvantages of this coating.
Foam products are sensitive to high temperatures, so they should not be placed in close proximity to chimneys or bright lamps. Under their influence, panels can melt and deform. Also, products from some manufacturers do not tolerate exposure to ultraviolet radiation well: the surface may turn yellow and lose strength.
These disadvantages cannot be called critical; they should simply be taken into account when choosing a brand and when choosing.
It is important to purchase quality tiles made of polystyrene foam from trusted manufacturers.
Foam tiles can vary greatly in quality and geometric parameters. That is why it is worth paying attention to the manufacturer. Which companies produce quality products?
The products are of quite decent quality, have standard technical characteristics, and are easy to install.
It should be noted that the options of the presented brands are low-budget and are of average quality. You should not use tiles from these manufacturers in areas with increased temperature conditions humidity level.
Improved quality products are offered trade marks"Armstrong", "Lily", "Ormit". True, the cost of tiles from these companies is an order of magnitude higher.
A rich and varied assortment of samples of foam ceiling tiles can be found in company catalogs, for example, in. The company’s official website offers any construction products that can be selected and purchased even via the Internet.
Let us remind you once again that gluing foam tiles is as easy as shelling pears. But this is despite the fact that you are determined to carry out the process competently and accurately. The “slip-and-dagger” work will immediately reveal itself: unevenness or gaps between the slabs will be noticeable. So you should be prepared to carefully follow the tile installation instructions.
Calculating the number of slabs is not difficult. The most popular are square slabs with standard sizes 50*50 cm. There are also small panels 30*30 cm. Rectangular tiles usually correspond to dimensions 100*16.5. Whatever the size of the products, the calculation of the tiles is carried out in the following way:
Don't forget to buy a foam ceiling plinth. Usually its length is 1 meter.
Surface preparation does not require serious effort. The main thing is to clean off the old coating and remove dirt. If this is not done, the likelihood of detachment of the foam boards increases. Serious unevenness must be filled: obvious displacement individual elements will lead to distortion of the pattern and rapid detachment. You don’t have to bother with minor flaws: flexible and soft slabs will hide them perfectly.
Before starting work, it is advisable to prime the entire area. This will increase the adhesion of the adhesive.
Let it be known to the novice amateur craftsman: foam tiles should be glued not from the edge of the ceiling, but from the center point. To determine it, pull two cords diagonally. The intersection point will be the center. If there is a chandelier in the center of the ceiling, then it will become the starting point.
In addition, the tensioned threads will indicate the correct path for guiding the slabs. You should not move by eye: there is a very high probability that the line of joints will shift. The final result will not please you: the curved direction of the rows will be very obvious.
Not all types of glue can provide a good connection between the tiles and the ceiling.
What adhesives can be used for installing foam tiles?
There is a Chinese adhesive composition - “Dragon”. This glue is cheaper, but its consumption is an order of magnitude greater.
When choosing, consider not only the quality and cost, but also the glue consumption per area.
And one more important nuance: for installing slabs in rooms with high humidity, it is better not to purchase water-based glue.
If we start the installation from the chandelier, then in each of the plates we cut off the corners for the hole from which the electric wire extends.
The nuances of application depend on the type of glue. The polyurethane composition is applied pointwise only to inner side slabs Other types of glue are applied with a brush not only to the entire inner surface slabs, but also on the ceiling, smearing it over the entire area. There are also compositions that require aging. The subtleties of application are always described in the instructions included with each container of glue.
Next, we apply the tiles strictly according to the markings and press them with our palms over the entire surface. So, tile by tile, we move further in accordance with the direction indicated by the stretched cords. We glue the remaining rows parallel to the first. If the tiles provide a seamless surface, then at the end of the work it is necessary to fill the joints with white sealant.
Most likely, the tiles in the last rows will have to be cut. This is done easily using household scissors. But here you will have to measure the required fragment, so also have a ruler and pencil.
The final stage is gluing the foam plastic ceiling plinth.
You've learned how to install ceiling tiles, but that's not enough. It is also useful to know about caring for it during operation:
So, foam ceiling tiles will provide a beautiful surface with proper and careful installation. This great option for low-budget repairs and for those amateurs who prefer to do the finishing work themselves. Follow the instructions given in the article to create a wonderful ceiling that emphasizes the comfort and beauty of your home. IN .
And he will tell you how to properly hang wallpaper on the ceiling.
There is a wide range of materials available for the design of ceiling surfaces. It could be plastic vinyl wallpapers or even regular plaster.
One of the solutions is foam ceiling tiles. They are affordable, but at the same time practical and very attractive.
The fastest and most cost-effective way to make the ceiling in your home beautiful is to buy foam ceiling tiles. This kind of material will help decorate any room.
It is suitable for offices, living spaces and even restrooms. If a question arises, how to paint foam ceiling tiles, then the answer is simple - any paint.
Is environmentally friendly pure material. The main advantage of tiles is compliance technical characteristics and prices. Designers all over the world have noted that such tiles are a good helper in decorating an apartment. It behaves well in rooms with high humidity and temperature changes.
Nowadays there are a huge number of tile modifications on the construction market. You can choose an ornament to suit every taste. The big plus is that it lends itself well to painting and visually smoothes the ceiling. Foam ceiling tile size depends on its type.
One of the advantages of ceiling tiles is that the pattern is uniform, but with a large number of seams. The slabs are installed very quickly. All these quality characteristics make this kind of material in demand.
If you don't like the seams on the ceiling, you can use a different type of tile. They are called seamless. The price will be higher, but the result is worth it. Panels of this shape look good in large rooms And office premises. All tiles of this type will only be in snow-white shades.
There are 3 ways to produce foam tiles:
The pressing method involves compression during the production of foam using a press. Such slabs will have a thickness of about 0.7 centimeters. Subsequently, the products are compacted and a pattern is applied to them.
In order to obtain thicker products, there is an injection method. IN in this case slabs are cast in a mold using high temperatures Oh. The resulting products will be the most expensive. The thinnest slabs are those produced by extrusion.
The variety of ceiling tiles makes this material very popular. The shape of foam tiles is:
As a rule, the slabs are made square. This is done for comfort in gluing them. But in Lately It is also possible to find rectangular slabs. They are more practical to use when decorating ceilings in large rooms. They will help reduce material consumption.
The size of the slab can be:
The most popular size of slabs is 50*50 centimeters, but there are also slabs - 30*30. Depending on the production method, they are:
The first slabs will be the most affordable. They will be grainy in type and usually white in color. Due to this type of production, the slabs are not very durable and the seams are clearly visible. There are errors in the manufacture of slabs, so cracks may appear when gluing the slabs.
When injected, the slabs are of high quality. The main characteristics of the products will be: correct shape, barely noticeable seams and a large number of plate designs.
When produced by injection, the slabs turn out to be off-white in color, so they are subsequently coated special film. This kind of material will be the most durable, but also quite expensive.
When finishing, the surface may look like this:
The most popular of them is laminated. After gluing the boards, the material is covered with film. This significantly increases the quality characteristics of a particular material. Such foam ceiling tiles in the kitchen, will look more than attractive.
Like any building material, tiles have their pros and cons. The advantages include:
Polystyrene foam tiles have high thermal and sound insulating qualities and are also lightweight. This makes it possible to carry out installation without the help of third parties.
It is also distinguished by its own decorative and a large number invoices Every buyer can buy foam ceiling tiles perfect shape. The ceiling, which is covered with such material, is not afraid of moisture and high temperature.
You can glue such tiles yourself without the presence of a specialist. However, despite a large number of advantages, the material has a number of disadvantages:
Over time, such plates tend to turn yellow, especially in the kitchen and bathroom.
The disadvantages of foam tiles include their fragility and softness.
Installation of slabs includes a number of stages, namely:
First of all, before you start work, you need to calculate the amount of material that will be needed. To do this, it is enough to understand the length and width of the room.
By multiplying these characteristics, you get the area of the room. But buy slabs according to this calculation. It is necessary to take about 15% of the total calculation in reserve. The shape of the ceiling in many apartments is not ideal, so the calculation may be incorrect!
Foam Ceiling Tile Adhesive you need to choose carefully. The service life of the slabs depends on it. So, several types of tips when choosing glue:
In order to glue the tiles you need a tool. You only need a little of it, and it is quite accessible to anyone. This:
Before you start gluing the slabs, it is necessary to prepare the ceiling. So, you don’t have to remove the old coating if it is smooth, but if the surface is not smooth, then it definitely needs to be cleaned.
Equally important! If the ceiling is whitewashed, then the whitewashing must be removed; the tiles will not adhere to it! If there are cracks or holes, they are puttied. In order for the slabs and ceiling to adhere, it is primed. The primer must dry for at least 3 hours.
Next, the ceiling is marked and the center is determined. Diagonals are drawn from the corners of the room and their intersection is found. This is done in order to determine the amount required slabs. If the ceiling is uneven, then you need to buy more slabs to fill the gaps.
Wall gluing can be done parallel to the walls or diagonally. Glue is applied to the slab, and installation occurs from the corner of the wall. Press the tile well and wait about 3 minutes.
If excess glue appears, it can be easily removed with a sponge. All subsequent slabs are glued to the joint of the previous ones. It will take about a day for the ceiling to dry. How to glue foam ceiling tiles Of course, all that remains is to disassemble it and paint it.
The following paints are suitable for painting foam ceiling tiles:
All these types of paints dry quickly and apply in an even layer. If the tile has been laminated, then you shouldn’t even try to paint it. The paint will run off and the result is unlikely to please you.
If the surface of the tile is rough, then it is better to use a spray gun so that there are no smudges or gaps. The joints must be sealed with sealant. After that, apply and let it dry.
It is advised to choose paint from well-known manufacturers, and it must meet the following requirements:
As for the choice of color, it should fit harmoniously into the interior of the room.
Foam ceiling tile price varied and varies from $1 per square meter. This applies to ordinary products. If the tiles are produced by extrusion, then the price of the products will be about $12, but the service life is an order of magnitude longer.
Many consumers note that this material behaves very well in any room. And of course, a big plus when choosing is the price. From a wide range of finishing materials, foam tiles are inexpensive. On the negative side: over time it may turn yellow and burst.
Average term The service life of this material depends on the manufacturer and varies from 5 to 15 years. Great importance has a room in which the tiles were glued. If this is a room with high humidity, then the material will lose its performance properties earlier than in a dry room.
Polystyrene foam is a lightweight, cheap and very useful material for the home. If you want to quickly and inexpensively finish the ceiling, then be sure to consider the option of foam plastic. If you do the right pasting, and also select suitable material, then the result can please you for more than ten years! Get to know the types of foam boards and the functional features of each type.
Despite the popular belief that there is only one type of polystyrene foam, in reality there are as many as 3 types of foam plastic, which differ from each other in many respects. Therefore, it is important to know what each of them is.
There are three types of foam boards based on the type of production:
There are three types of them most the best option in terms of price and quality ratio it is injection. Therefore, if you want a durable beautiful tiles, choose exactly this type.
If you decide to use this particular material to decorate your ceiling, then it is recommended that you get acquainted with the advantages and disadvantages that it has this material.
The disadvantages of polystyrene foam include the following:
All the disadvantages of foam boards are more than offset by the advantages: cheap and lightweight polystyrene foam tiles will hide minor imperfections in the ceiling, and will also decorate the room with the proper approach to choosing a pattern and installation.
In order to paste the ceiling surface using foam boards, you must first check the condition of the original ceiling surface. Remember that slabs are indeed capable of hiding minor defects in the ceiling, but do not trust polystyrene foam with depressions and sagging of more than half a centimeter.
If your ceiling is relatively flat, clean and ready for pasting, then do the following:
To create the feeling of a relief or stretch ceiling, use seamless tiles made from the highest quality materials.
If you have already installed a ceiling made of foam tiles, then perhaps you need help in some issues regarding the operation of such a ceiling. The fact is that often with sloppy gluing one or more slabs may leave their original place. In this case, replacement of the tiles is necessary. If the fallen tile remains intact, then you just need to remove the remnants of the old glue and glue the part again. If a part breaks, you will have to look for the same one.
When purchasing a stove, be sure to count 5-10 pieces in case the stove is damaged. Perhaps in a few years you will not be able to find the tiles you need.
There is a way to minimize everything possible risks and troubles associated with foam ceilings. This method is to paint the ceiling.
What features should be taken into account if you decide to paint a foam ceiling:
The design of a room largely depends on how the ceiling looks. To make a beautiful surface for little money, you can glue neat, expensive slabs, and to strengthen positive effect use paint. If you want to make the room cozy and well-groomed, then ceiling tiles will allow you to independently transform a boring ceiling into a surface pleasing to the eye.
When a complex renovation of a room is carried out, the owners try to pay due attention to even minor details. When decisions are made about external matters, people try to be especially careful. The comfort of the entire room and the overall impression that is created upon entering it depend on the beauty and appropriateness of the colors of this part of the room. Many designers choose ceiling tiles as a finishing material. This decision is often dictated by its practicality and versatility.
If the method of production of these products is assessed, the following varieties are distinguished:
This foam ceiling tile, the price of which can rise above 500 rubles per package, is the most versatile. This species has many names by which users recognize it better. This repair material is often called laminated or extruded, which is suitable for these elements due to the peculiarities of the manufacturing technology.
Polystyrene foam is first converted into foam by exposure to special substances and temperatures. The tiles are shaped using a vacuum. This is the most beautiful, durable, rich, memorable and high-quality decor. It's quite interesting, but you have to choose suitable option can take a very long time, since there is a chance to find perfect coverage for the ceiling, appropriate in a specific interior. Sometimes adhesive for this type of foam ceiling tile is available in a liquid nail configuration.
When evaluating the shape of ceiling tiles, the following varieties can be distinguished:
Foam ceiling tiles are often divided into groups based on appearance. Usually, front side completely covered with a special film, which simultaneously performs both a protective and decorative function. It can be painted to match any elements. Typically the colors resemble wood, patterned fabric, ceramics or stone.
Recently, foam ceiling tiles have begun to be produced, the sizes of which differ from others, and you can paint them in the desired color yourself. That is, when choosing this building material, you do not have to decide on the required shade or pattern. This option allows you to give the tile the maximum suitable color to skillfully combine it with the rest of the decor in the room.
Such tiles are currently considered universal building material, therefore it can be used in any room, even for narrow-profile purposes. Typically, such elements are used for the living room, hall, personal account or bedroom. This building material is capable of visually making the ceiling higher, so it is especially appropriate in the listed rooms.
Foam tiles are very often chosen for the kitchen. It is very convenient to wash. Sound-absorbing foam tiles will look great and be beneficial in a child's room. This function is provided if it is installed, the availability of which should be checked in the instructions specific type products or directly from the seller. If you decide to use tiles to decorate a bathroom or toilet, materials with a smooth or slightly corrugated surface are selected.
Foam ceiling tiles have many positive qualities. The modern user cannot help but appreciate them. Usually they first talk about the various heat and sound insulating properties that all foam ceiling tiles have. The weight of such products is small, so their installation is quite easy. The material is also quite decorative. Even its simplified samples look interesting and can dilute even the most austere interior.
The finishing material is represented by a wide range of choices on the modern building materials market, so it will not be difficult to choose the optimal tiles, focusing not only on the style, design and size of these products, but also on the pricing policy.
If the ceiling is finished with these tiles, the owners can be sure that it will not succumb to rotting processes and will not become moldy even after a fairly long period of use. A surface coated with such material cannot be damaged by exposure to high humidity or constant dampness of the room. This building material is successfully used in buildings of any type.
Foam ceiling tiles can perfectly hide all irregularities, defects and protruding parts if they are laid according to all the rules. This building material is not only convenient, but also easy to interact with, so not only a professional, but also a beginner can complete the finishing. To process the tiles and adjust them to the desired width and length, just use a regular knife. Provide excellent appearance coating can be done by a person even without repair skills. Also, this material has an affordable price, which always influences the final decision when choosing it.
The ceiling is not durable enough. Repairs will have to be carried out regularly, but remember that during optimal time operation, which is provided by foam ceiling tiles, there are no complaints about the material. It does not release negative substances into environment, as it is correctly processed and covered with a protective coating.
When exposed to direct sunlight, the tiles gradually turn yellow. They can protect her from this blackout curtains on the windows. It would be even better to place the material where the sun’s rays do not reach the surface or only affect it for a short time.
Polystyrene foam does not have fire resistance, so it can become very dangerous if it catches fire. This is a huge disadvantage in products such as foam ceiling tiles. When mounting the lamp, you should remember that the lighting device cannot be mounted higher than 30 cm from the ceiling.
Let's figure out whether foam ceiling tiles are painted. It should be remembered that not all varieties of this material can be painted. If the coating is laminated, attempts to give it a different shade are in most cases useless or do not give a lasting positive result. If the tile is susceptible to painting, it is advisable to use a water-based or acrylic mixture. If the question is how to paint foam ceiling tiles, you must take into account all the indicators listed below.
When choosing paint, you should consider the quality of the coating. The degree of dullness, consumption, and the presence of antiseptic additives or protective elements in the composition are also important. Painting of foam ceiling tiles is done from the window. When performing work, you must constantly maintain smooth movements. If everything is done efficiently, the ceiling tiles will look great and beautifully complement the interior of the room.
